原创力文档- 1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
- 2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击 这里二次下载。
- 3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
- 4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
- 5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
- 6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
- 7、VIP文档为合作方或网友上传，每下载1次， 网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档
查看更多
1、启动前，应关闭排出阀并打开进口阀进行灌泵，并打开 冷却水。 2、启动电机检查旋挂方向是否正确。 3、离心式卫生泵正转后，慢慢打开排出阀。 4、通过排出阀的调节，液体的流量、扬程及效率应满足设计要求，不宜随意增大流量。 5、在运行中应注意机器的噪声和振动是否正常，如发现异常应立即停车检查。 6、离心泵在正常使用时，机械密封泄漏料量不大于3ml/h并应经常检查密封件磨损情况。 7、停车前应关闭排出阀，使泵卸载并防止液体倒流，然后关闭电机，关闭冷却水。 卫生泵操作规程 知识回顾Knowledge Review * ``````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````` 设备操作及原理 板式换热器的操作规程 编号：MN/BL/HZ-01/JS/1008-03-06 1、使用前检查换热器的出料管是否畅通，在确保畅通的情况下方可过料； 2、先打开冷水出水阀，再开进水阀，热后启动均质泵送入需冷却的物料，把片内剩余的水逐渐顶出，直至完全是物料时，方可把物料送入贮物料缸进行暂存； ３、过料后，关闭进水阀； ４、过料完毕后，用清水将设备中残留的物料顶出直至流出的是水而无物料痕迹； ５、根据使用情况，每隔三星期打开板式热交换器各传热板片，过察清洗是否有效，并用棕刷刷洗板片表面的沉积物，如刷洗困难，可使用稀硝酸处冷，再用清水洗净，最后装配妥善。 出水阀 进水阀 出料口 进料口 进水阀 出水阀 老化缸操作规程 编
文档评论（0）