(完整word版)螺纹基本尺寸对照表.docVIP

英制管螺纹基本尺寸及公差（牙形角 55o） BSPP 螺纹代号 G1/8″× 28 G1/4″× 19 G3/8″× 19 G1/2″× 14 G5/8″× 14 G3/4″× 14 G1″× 11 G1.1/4″× 11 G1.1/2″× 11 G2″× 11 G2.1/2 ” X11 G3” X11 G3.1/2 ” X11  基本直径 内螺纹 外螺纹 A 级 B 级 大径 中径 小径 中径公差 小径公差 中径公差 大径公差 中径公差 大径公差 9.728 9.147 8.566 +0.170 +0.282 0 0 0 0 0 -0.107 -0.214 -0.214 -0.214 13.157 12.301 11.445 +0.125 +0.445 -0.125 -0.250 -0.250 0-0.250 16.662 15.806 14.950 +0.125 +0.445 0 0 0 0 0 0 -0.125 -0.250 -0.250 -0.250 20.955 19.793 18.631 +0.142 +0.541 0 0 0 0 0 0 -0.142 -0.284 -0.284 -0.284 22.911 21.749 20.587 +0.142 +0.541 0 0 0 0 0 0 -0.142 -0.284 -0.284 -0.284 26.441 25.279 24.117 +0.142 +0.541 0 0 0 0 0 0 -0.142 -0.284 -0.284 -0.284 33.249 31.770 30.291 +0.180 +0.640 0 0 0 0 0 0 -0.180 -0.360 -0.360 -0.360 41.910 40.431 38.952 +0.180 +0.640 0 0 0 0 0 0 -0.180 -0.360 -0.360 -0.360 47.803 46.324 44.854 +0.180 +0.640 0 0 0 0 0 0 -0.180 -0.360 -0.360 -0.360 59.614 58.135 56.656 +0.180 +0.640 0 0 0 0 0 0 -0.180 -0.360 -0.360 -0.360 75.184 73.705 72.226 +0.217 +0.640 0 0 0 0 0 0 -0.217 -0.434 -0.434 -0.434 87.884 86.405 84.926 +0.217 +0.640 0 0 0 0 0 0 -0.217 -0.434 -0.434 -0.434 100.330 98.851 97.372 +0.217 +0.640 0 0 0 0 0 0 -0.217 -0.434 -0.434 -0.434 英制锥管螺纹基本尺寸及公差（牙形角 55o） BSPT 基面上的直径 基准长度 有效螺纹长度 圆锥内螺纹基面轴向 螺纹代号 大径 中径 小径 基本 最大 最小 基本 最大 最小 位移偏差（ ± mm） R1/8″× 28 9.728 9.147 8.566 4.0 4.9 3.1 6.5 7.4 5.6 1.1 R1/4″× 19 13.157 12.301 11.445 6.0 7.3 4.7 9.7 11.0 8.4 1.7 R3/8″× 19 16.662 15.806 14.950 6.4 7.7 5.1 10.1 11.4 8.8 1.7 R1/2″× 14 20.955 19.793 18.631 8.2 10.0 6.4 13.2 15.0 11.4 2.3 R3/4″× 14 26.441 25.279 24.117 9.5 11.3 7.7 14.5 16.3 12.7 2.3 R1″× 11 33.249 31.770 30.291 10.4 12.7 8.1 16.8 19.1 14.5 2.9 R1.1/4″× 11 41.910 40.431 38.952 12.7 15.0 10.4 19.1 21.4 16.8 2.9 R1.1/2″× 11 47.803 46.324 44.845 12.7 15.0 10.4 19.1 21.4 16.8 2.9 R2″× 11 59.614 58.135 56.656 15.9 18.2 13.6 23.4 25.7 21.1 2.9 R2.1/2 ” X11 75.184 73.705 72.226 17.5 21.0 14.0 26.7 30.2 23.2 3.5 R3” X11 87.884 86.405 84.926 20.6 24.1 17.1 29.8 33.3 26.3 3.5 R3.1/2 ” X11 100.