ma5605配置操作手册.docxVIP

MA5605配置操作手册 相关命令： show time show versi on show board 0 show runnin g-c onfig i：改名字 MA5605(c on fig)#host name xiaowei 2:改用户密码 MA5605#user password old password: adm in （改后新密码，如果不需要设置此步不需要做）New password(20 chars): admi nmin （改后新密码，如果不需要设置此步不需要做） Con firm new password:admi nmin 3:改时间 3:改时间 MA5605#time （一般不用配置） 进入LAN配置模式设置 LAN端口状态 int lan 0/0 MA5605(co nfig-LAN-0/0)#port m ode tagged- mode{tagged,u ntagged}:tagged {n egotiate ,non-n egotiate}:non-n egotiate {full-duplex}:full-duplex speed{100m}:100m Set successfully. MA5605(config-LAN-0/0)#vlan %d ( 业务 VLAN) vla nld{1-4095}:1554 Add VLAN successfully, VLANID = MA5605(config-LAN-0/0)#vlan %d ( 管理 VLAN) vla nld{1-4095}:1000 Add VLAN successfully, VLANID = 5.设置VLAN （打开带内通道） MA5605(config)#nms vlanId{1-4095}:1000 (网关 vlan ) Are you sure to set the inband VLAN to 1? (y/n) [n]:y 设置级联转发 VLAN ( 注意如果是级连要此步，不是侧不要 MA5605(config-LAN-0/0)#cascade {forward,number}:number num{0-3}:1 Set cascading number successfully. MA5605(config-LAN-0/0)#cascade {forward,number}:forward {vlan,all}:all start-vlanId{1-4095}: end-vlanId{1-4095}: Set 16 cascading VLAN successfully. VLAN 和级联层数（设备分配的范围内。?? 如果有级联设备，则上级设备需要设置转发(下级设备的) 设置 VLAN 和级联层数（ 设备分配的范围内。 ?? 级联 MA5605 下级的 VLAN ID 必须在上级 MA5605 设置设备 IP 地址 MA5605(config)#at mlan ip-address ethernet ip-addr:218.92.157.150 net mask:255.255.255.248 Set successfully 配置到上连设备的系统路由 MA5605(config)#at mlan ip-route ip-addr:0.0.0.0 net mask:0.0.0.0 gateway :218.92.157.145 Add route successfully. 配置可接受访问列表 MA5605(config)#at mlan ip-access start-ip :218.92.157.145 ( 路游地址 ) end-ip:218.92.157.137 mask:255.255.255.255 可把县局要维护的计算机、交换机地址配置进去） 设置 ADSL 线路模板参数 e are neglected. 加模板 ) e are neglected. 加模板 ) During input,press Q to quit,then settings at this tim Select the line profile type 1-adsl 2-adsl2+(1~2) [1]: (2 Will you set basic configuration for m odem? (y/n) [n]:y Note: Setting to these m ode of G992.3~5 will lead that the adsl ports that are not support adsl2+ not be activated ADSL operating m ode: 0: All(G