塑胶模具DFM翻译参考.docxVIP

成型吨位(Machine Tonnage) 成型周期(Molding Cycle) 取数(Cavities)浇口（Gate）流道重量(Runner weight) 寿命(Mold life) 成型吨位(Machine Tonnage) 成型周期(Molding Cycle) 取数(Cavities) 浇口（Gate） 流道重量(Runner weight) 寿命(Mold life) 前模钢料(Cavity steel) 后模钢料(Core steel) 行位/斜顶钢料(lifter steel) 模胚形式(Mold type) 热流道(Hot Runner) 其他配件(Others) 16.顶针及方顶印凹 0.1mm 以下 EP and square EP mark concave 0.1 max is there any concern about the thin material (filling and ejection)?薄胶处有无问题？ 17.材料及模穴号（1,2）凸 0.2mm Material and Cav no. convex 0.2mm 孔处 PL 段差 孔处 PL 段差 COR 凹 0.1mm 以下 There is step at PL of hole, concave 0.1mm max. Could 13.后模镶件印凹 0.1mm 以下 Core insert mark concave 0.1mm max 1. 1.为预防粘前模，外侧面斜度由 0.5o 均改为 1o To avoid sticking to cavity, change outside surface draft from 0.5oto 1o 3. 3.红色区域可能出现缩水，是否接受？ There may be sink mark on red surface, could you accept that? 10. 10.紫色面做 5 加胶插穿斜度(加胶 0.1mm MAX) Add plastic on purple surface with 5 degree shut-off draft (add 0.1mm max plastic) Zebra 20Jan2016: this surface mates to another flat surface; adding material will cause issues with assembling part P1082228 into printer 这种表面配合到另一平面上; 添加材料会导致零件 P1082228 装配到打印机产生问题 11.PL 11.PL 插穿段差 CAV 凹 0.15mm 以下（对侧同） Step exist on PL shut-off surface, suggest that core concave 0.15mm max ( same for opposite side) 扣易粘前模，需如图增加前模镶件和弹块， 扣易粘前模，需如图增加前模镶件和弹块，PL 如图更新。 Hook easily stick to cav., need to add insert and slider as picture. PL is updated as picture shows. 12. 12.图示柱子根部做火山口，改善现状部品缩水。 Make break sharp in the area as shown above to combat sink marks 16. 16.前模互换镶件（3 款互换），与现状部品完全一致 Interchangeable cavity inserts (3 ones), Same feature as those in the old-tool time 19. 19.针阀式热咀进浇（?5），残留不超出凹位。 Valve gate(?5), vestige to be flush to be in line with the concave Min() 1Causes of the cracks on the：tool a钢料太硬造成钢料太脆，从而造成钢料易裂，建议用软钢料开新 模.For steel performance, the harder, the more fractural. Based on this reason, a relatively low h ard steel is suggested to be used for the new tool. b模仁两侧边的钢料厚度不够，现实际为41mm，而深度有59mm，建议两侧钢料壁厚加到 60mm. The nominal thickness of