目视检验规范演示文稿.pptVIP

目视检验规范演示文稿 当前第1页\共有33页\编于星期一\8点 目视检验规范 当前第2页\共有33页\编于星期一\8点 目視檢驗規范標准IPC610 1.允收標准2.拒收標准 当前第3页\共有33页\编于星期一\8点 零件本體僅下方有二接觸點的零件(Chip Components/Bottom Only Terminations cont.) – 偏移 (Shift) 允收 (Target Condition) 零件黏焊於錫墊中心位置, 沒有任何偏移. ? No side overhang. 允收極限 (Acceptable) 零件往錫墊寬邊(A)偏移, 但零件 本體寬邊(C) 有75% 以上焊接於 錫墊上. 零件本體與電路板錫墊間(G)錫 厚至少0.2 mm. Side overhang (A) is allowed if minimum end joint width (C) requirements are met.Minimum is 75%. ?Minimum thickness (G) is 0.2 mm unless satisfactory cleaning can be demonstrated with reduced clearance. 拒收 (Nonconforming Defect) 零件往錫墊寬邊(A)偏移, 且零 件本體小於75% 寬邊(C) 焊接 於錫墊上. ? 零件往錫墊長邊(B)偏移. Side overhang (A) is allowed if minimum end joint width (C) requirements are met. Minimum is 75%. ?Minimum thickness (G) is 0.2 mm unless satisfactory cleaning can be demonstrated with reduced clearance. 当前第4页\共有33页\编于星期一\8点 零件本體有1,3,5面矩形金屬焊接點  (Rectangular End Components-1,3or5 side Termination) – 偏移 (Shift) 允收 (Target Condition) 零件金屬部份黏焊於錫墊中 心位置, 沒有任何偏移. 零件 本體錫墊完全沾錫. No side overhang. Side joint length (D) equals component termination length. 允收極限 (Acceptable) 零件往錫墊寬邊(A)偏移, 但 零件本體金屬焊墊寬邊(W) 75%以上焊接於電路板錫墊上. End joint width (C) is 75% width of component termination area (W) or 75% width of PB land (P), whichever is less. 拒收 (Nonconforming Defect) 零件往錫墊寬邊(A)偏移, 但零 件本體不足75% 寬邊(C)以上焊 接於電路板錫墊上. 零件往錫墊長邊偏移(B). Side overhang (A) causes minimum end joint width (C) requirements not to be met. ? End overhang (B) is not permitted. 当前第5页\共有33页\编于星期一\8点 零件本體有1,3,5面矩形接觸點 (Rectangular End Components-1,3or5 side Termination) – 偏移 (Shift) 允收 (Target Condition) 零件黏焊於錫墊中心位置, 沒有任何偏移. 零件本體錫 墊完全沾錫. No side overhang. 允收極限 (Acceptable) 零件往錫墊寬邊偏移, 但零件 之焊接面佔75% 以上. End joint width is 75% width of component termination area or 75% width of PB land , whichever is less. 拒收 (Nonconforming Defect) 零件往錫墊長邊偏移. End overhang is not per