焊接外观检查手册.docxVIP

焊接结构件目视检查 Fabrication Visual Inspection Criteria ? 焊缝术语知识 ? 焊缝术语知识 Weld terminology knowledge Page PAGE Page PAGE # of 36 ? 焊缝术语知识 ? 焊缝术语知识 Weld terminology knowledge Page PAGE Page PAGE # of 36 Page PAGE Page PAGE # of 36 目录 Content TOC \o 1-5 \h \z \o Current Document 目录 Content 1 焊缝术语知识 Weld terminology knowledge 2 焊接方法和位置知识 Weld methodposition knowledge 3 ■焊接位置图示Weld position map 4 ■定义 Definitions (1) 5 ■定义 Definitions (2) 6 ■定义 Definitions (3) 7 ■焊接波纹 Waving on weld 8 \o Current Document ■角焊缝 FiLLET WELD - UNEQUAL SIZE 9 \o Current Document ■未焊满 Underfill 9 \o Current Document ■焊道之间的沟槽Inter beads valley 11 ■不规则的宽度/焊接表面Irregular width/weld surface 12 未焊透/过度焊透 Lack/excess of penetration 12 \o Current Document ■焊接起始和收尾Weld start and end 13 ■焊接接头Weld head 15 \o Current Document ■拐角处焊接 Weld on the corner 16 ■焊瘤 Lumps 17 ■角度偏差Angle deviation 18 ■重叠 OVERLAP 18 \o Current Document ■气孔 Porosity 19 \o Current Document ■飞溅和表面渣 Spatter surface slag 20 \o Current Document ■打火 Arc strikes 21 ■咬边 Undercut 22 \o Current Document ■弧坑 Weld crater 23 \o Current Document ■氧气切割的不良Oxy cutting defects 24 \o Current Document 边缘毛刺的去除Sharp edges removal 25 局部过热Local excess HEATING 26 工件钢印识另U Component punched identification 27 \o Current Document ■坡 口准备 Bevel preparation 29 去除临时支撑时产生的凹痕和深坑Dents deep cuts at temporary support REMOVAL 30 ■焊工钢印Weld stamp 31 ■焊接气体种类和流量控制Weld gas type and flow rate 32 预热范围及热输入控制Preheat range and heat input 33 \o Current Document ■焊接接头控制Weld head control 34 焊道顺序 The weld bead sequence 35 \o Current Document ■注释说明 GENERAL notes 36 Toe—焊趾 Face—焊缝表面 Reinforcement—余高 Weld Size—焊缝尺寸 Fusion Face一熔合面 Depth of Fusion—熔合深度 Weld Interface一熔合线 Fusion Zone一熔合区 Root一焊根 Root Reinforcement一背面余高 Toe—焊趾 Weld Interface一熔合线Weld Size—焊缝尺寸 Face—焊缝表面 Actual Throat—实际焊喉 Theoretical Throat—有效焊喉 Root—焊根 Weld Interface一熔合线 Weld Fusion Face一熔合面 Depth of Fusion—熔合深 度Fusion Zone一熔合区 ■焊接方法和位置知识 ■焊接方法和位置知识 Weld methodposition knowledge Pa