涵洞计算设计说明.pdfVIP

一、圆管涵工程量的计算

此例管涵为K0+120处的正交员管涵其孔径为1.25米，进出口

形式采用八字墙形式，洞底中心标高为89.4米，路线设计标高为

91.9米，路面边缘标高为91.855米，其计算图见后。

m=1.5

n=5

H=1.97m

h=0.85m

i=0.03

a=1.62

c=0.46

涵长的计算;

Li=[B:+m(H:-a)+c]/(1+im)

=[6+1.5x(2.455-1.62)+0.46]/(1+0.03x1.5)=7.38m

L=2L:=14.76m取L-15m

1.翼墙墙身

V=0.5cm(H-h)+m(H-h)/6n

=0.5x0.46x1.5x(1.97-0.85)+1.5x(1.97-0.85)/6x5)

=1.44㎡

两墙身=2x1.44=2.88m

2.翼墙基础

e:=12，ez=11，d=0.4，e=0.1

V==1.5x(0.46+0.12+0.11)(1.97-0.85)*0.4+[1.5/(2*5)]x

(1.97-0.85)x0.4+(0.46+0.12+0.11+0.85/5)x0.1*0.4

V_=0.687m

2V==2x0.687=1.374m

3.进出口铺底

V=2x(1.49+1.49+0.98x2)x(1.68+0.1)x0.5x0.25-1.95m

4.截水墙

V=2x{[1.49+2x0.98+1.49+2x(168+0.1-0.3)tg30]x0.3x0.5}

x(0.6-0.25)=0.7m

5.端墙墙身

V=2x{0.4x(1.25+0.12+0.6)x(2x0.46+2x0.12+1.25)x

0.745x0.4}=1.2m

6.端墙基础

V=2x[0.6x0.4x(2x0.46+2x0.12+1.25)]=1.2m

7.15号混泥土帽石

V=2x[(0.25x0.4-0.5x0.05x0.05)x(2.41+0.05x2)]=0.5m

8.砂砾垫层

V=0.3x2.75(7.33x2-2x0.4)=11.5m

9.15号混泥土护管

V=2.75x0.745x(7.33x2-2x0.4)-0.5x0.745x(7.33x2-0.4

10.人工开挖土方

V=30.5㎡

二、盖板涵工程量的计算

K1+030处涵洞为4x3的正交盖板涵，其洞口的进出口形式为采

用八字墙形式，其洞底标高为89.0米，路面设计高为94.3米，其

计算图式见后。

m=1.5H=3.30mh=0.20mG=4.65mn=3.75i=0.03

涵长的计算:

L=[B:+m(H:-a)+c]/(1+im)

=[6+1.5x(5.255-3.55)+0.4]/(1+0.03x1.5)=8.57m

L=2L:=17.1

取L=18m

1.翼墙墙身

V=0.5cm(lf-h)+m(Ir-h)/6n

=0.5x0.58x15x(330-0.20)+1.5x(330-0.20)/6x3.75

=7.1m

两墙身=2x7.1=14.3m

2.翼墙基础

V=m(c+ete:)(H-h)d+[m:/(2n)](Hr-h)d+(cte:te.+h/n;)ed

e:=12，e:=11d=0.6，e=0.1，no=3.75

V=1.5*(0.58+0.12+0.11)(3.30-0.20)*0.6+[1.5/(2*3.75)

*0.1*0.6

Vu=3.81m

2Vu=2*0.687=7.62m

3.进出口铺底

V=2x[(3.76+3.76+2.51x2)x0.5x4.35x0.4]=21.82m

4.截水墙

V=2x([2x(3.76+2.51x2)+0.4tg30x2]x0.4x0.5x1.2}=8.65m

5.混泥土帽石

V=2x[(0.25x0.4-0.5x0.05)x4.16]=0.82m

6.涵身基础

V