网站大量收购独家精品文档,联系QQ:2885784924

数字频率计课设论文.doc

  1. 1、本文档共26页,可阅读全部内容。
  2. 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
  3. 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载
  4. 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
数字频率计课设论文.doc

编号: 课程设计说明书 题 目: 数字频率计 院 (系): 电子工程与自动化学院 专 业: 自动化 学生姓名: 黎桂 学 号: 1000810216 指导教师:龙超 姜辉 赵学军 陈乐庚 潘明 刘振丙 题目类型: 理论研究 实验研究 工程设计 工程技术研究 软件开发 2013年 7 月 5日 摘 要 频率测量是电子学测量中最为基本的测量之一。频率计主要是由信号输入和放大整形电路、单片机模块及显示电路模块组成。STC12C5A60S2单片机是频率计的控制核心,来完成它待测信号的计数,译码,显示。利用它内部的定时/计数器完成待测信号频率的测量。 在整个设计过程中,所制作的频率计采用外部分频,实现1Hz~650KHz的频率测量,而且可以实现量程自动切换流程。以STC12C5A60S2单片机为核心,通过单片机内部定时/计数器的门控时间,方便对频率计的测量。其待测频率值使用四位共阳极数码管显示,并可以自动切换量程,单位分别用一个LED灯的亮灭来表示。本次采用单片机技术设计一种数字显示的频率计,具有测量准确度高,响应速度快,体积小等优点。 关键词:频率计;单片机;计数器;量程自动切换 Abstract Frequency measurement is the most basic measurement in Electronic field. A simple frequency meter mainly by the signal input and amplifying circuit, microcontroller moduleand display module. STC12C5A60S2 MCU is the control core frequency of dollars to complete its count of the signal under test, decoding, display and control of the frequency division ratio. Using its internal timer or counter to complete the signal of the under test cycle / frequency of measurement. Throughout the design process, periodic measurement of the frequency meter application and the corresponding mathematical treatment to achieve 1Hz ~ 650kHz frequency measurements, and can automatically switch the flow to achieve scale. To the core of STC12C5A60S2 microcontroller, with the MCU internal timer / counter gate time, it can be easier for frequency measurement. With the LED light /off to represent the range,The use of microcomputer technology to design a digital display of frequency meter, have a measurement of high accuracy, fast response, small size and so on. KEY WORD: Frequency meter; single chip; counter; range automatically switch 目 录 引言 1 1 课题研究的内容和要求 1 2 系统方案设计 1 2.1总体方案的设计 1 2.2各个模块的方案分析 3 2.2.1 单片机系统介绍 2 2.2.2 放大整形模块介绍 4 2.2.3 显示模块 5 3 系统硬件设计 5 3.1单片机主控制器模块 5 3.1.1复位电路及时钟电路 5 3.1.2引脚功能 6 3.2 放大整形模块 8 3.3 显示模块 8 4 系统软件设计 9 4.1 几个重要的子程序 10 4.1.1 控制程序 10 4.1.2 数码转换程序 13 4.1

文档评论(0)

我的文档 + 关注
实名认证
内容提供者

该用户很懒,什么也没介绍

1亿VIP精品文档

相关文档