油盖轴承外挡装配间隙标准.docVIP

油盖轴承外挡装配间隙标准 给内挡油盖加满润滑脂，轴承加轴承室1/2—2/3容积、质量合格的二硫化钼#3锂基脂，要求尽量将油脂压进轴承间隙中去，注意保持轴承外圈个表面干净。 To block the oil cap filled with grease, bearing and bearing housing 1/2-2/3 volume, quality qualified molybdenum disulfide # 3 lithium base grease, the requirement of oil pressure as much as possible into the bearing clearance, pay attention to keep the bearing outer ring surface clean. 表1 SKF轴承标准轴承间隙 滚珠轴承 滚柱轴承 孔径（d mm） 径向间隙（μm） 孔径（d mm） 径向间隙（μm） 轴承型号 普通级 C3级 轴承型号 普通级 C3级 6220 12 36 30 58 NU220 50 85 75 110 注： 当间隙的后缀与P4、P5、P6结合，间隙后缀中省去C，例如：P6+C3 P63 电动机各部件回装，通380v电源试转 380 v power supply motor parts back, try to turn □ 电动机定子导风筒、前后端盖、外挡油盖、加热管路、测温探头、风扇、风罩和风冷却器等按原记号和先后顺序回装，吊车装端盖时注意保持轴承在轴承室中间部位，外挡油盖并检查装配情况是否良好，在装风冷却器之前，检查定、酿酒设备转子铁芯通风孔对应3/4以上，要求紧固螺丝上齐上紧，风冷却器带紧或扣紧，密封条密封严密。 - air duct, motor stator cover front and back end cover, gear oil, heat pipe, temperature sensor, fan cover, wind and wind cooler, etc. According to the original mark and order back to the pack, keep the bearing in the middle of the bearing chamber while loading an end cover parts, the oil retaining cover and check the assembly situation are in good condition, before install air cooler, check, the rotor iron core vents corresponding 3/4 above, require neat, tightening up the fastening screw in the cooler wind belt tight or fastening and sealing to seal tightly. □ 用手正反方向盘动转子转动4圈及以上，无机械卡涩或摩擦声，且转子每次停下来时应不在同一个位置。 and the steering wheel with your hand move rotor rotating four laps and above, no mechanical jamming or friction sound, and the rotor should be not in the same place every time they stop. □ 检查电动机接线盒密封是否严密，更换老化的密封垫，更换周期不得超过2个大修周期，检查电动机外壳清洁，铭牌完好。 - check whether the motor terminal box seal is tight, replace the aging of the gasket, the replacement cycle should not exceed 2 overhaul cycle, check the motor shell is clean, nameplate in good condition. □ 检查电动机绝缘，接380V电源试转电动机的空转达20分钟及以上，检查酱油电动机无异音和振动过大，要求空转时边转动边加油改善轴承润滑。 - check the insulation of the motor, 380 v power supply to try convey more than 20