出入段线占用金果幼儿园的报告2013.03.15.docVIP

出入段线占用金果幼儿园的报告2013.03.15.doc

  1. 1、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。。
  2. 2、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载
  3. 3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
  4. 4、该文档为VIP文档,如果想要下载,成为VIP会员后,下载免费。
  5. 5、成为VIP后,下载本文档将扣除1次下载权益。下载后,不支持退款、换文档。如有疑问请联系我们
  6. 6、成为VIP后,您将拥有八大权益,权益包括:VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
  7. 7、VIP文档为合作方或网友上传,每下载1次, 网站将根据用户上传文档的质量评分、类型等,对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档
查看更多
出入段线占用金果幼儿园的报告2013.03.15

成都地铁7号线土建5标 川师车辆段出入段线 占用金苹果爱弥儿幼稚园地块的报告 编 制 : 审 核 : 审 定 : 中铁九局集团有限公司 成都地铁7号线土建5标项目部 2013年月日 序号 项目 单位 数量 备注 1 施工场地临时占地 ㎡ 2915㎡ 管线迁改、主体施工, 施工场地临时占地 2 围墙长度 m 340.7m 3 洗衣房占地 ㎡ 1个 面积:29㎡ 4 车库占地 ㎡ 1个 面积:114㎡ 5 水池占地 ㎡ 1个 面积:41㎡ 6 游戏区占地 ㎡ 315㎡ 7 门卫室 座 1座 8 绿地面积 ㎡ 1486㎡ 9 跑道 m 25 宽3米 10 走廊 m 15 宽3m,走廊上部为绿化 三、存在问题 川师车辆段出入段线主体施工及交通疏解围挡需临时占用占用金苹果幼儿园部分地块2915㎡,并需拆除幼稚园大门及340.7m围墙,拆除一座洗衣房,一座门卫房及一座车库、部分跑道、走廊、水池等。 四、占地时间安排 占地时间为2013年5月1日至2014年12月30日,共计20个月,610天; 附图 出入段线占地示意图 附图 出入段线占地照片 中铁九局集团有限公司 成都地铁7号线土建5标项目部 2013年3月18日 金苹果幼儿园门卫室 金苹果幼儿园水池 金苹果幼儿园绿地 金苹果幼儿园游戏区 金苹果幼儿园跑道 金苹果幼儿园车库 金苹果幼儿园洗衣房 金苹果幼儿园走廊 the same direction of rotation 90 ° or 180 ° for; after each disc rotor when measuring position alignment of the two half coupling constant, should also be in terms of accuracy and consistency. Surface deviation measurement, must in every 180 degrees corresponding to the two radii are equal to each other in order to eliminate errors caused by movement of the rotor. Only a support bearing of the rotor, WA couplings, such as the use of temporary leave the Center, should pay attention to keep the rotor in the measuring process in the center of the bearing oil retaining the nest does not change. Steam oil block, there should be sufficient clearance between the rotor and, in rotors make sure rotor is not on the block or seal oil. At the time of measurement, connections are not allowed between two rotors, each in a free State. Not allowed in case of assembled sleeve, Center work on the toothed coupling. Coupling tool should have adequate stiffness, installation must be secure and reliable. Coupling Center using a dial indicator, the table should be put in prison and avoid touching, to ensure correct measurement. Coupling disc after a week to return to the original position, circumference of dial gauge reading should be able to go back to the original value. When measuring the clearance of end, into the feeler of the gap should not exceed four at a time, when t

文档评论(0)

gov469 + 关注
实名认证
文档贡献者

该用户很懒,什么也没介绍

1亿VIP精品文档

相关文档