自动化单片机..docxVIP

嵌入式微控制器作业0901130212，自动化1302，黄强第六章6.10 单片机系统晶振为11.0529MHz，串行口工作于方式1，波特率为4800bit/s，从串行口输出字符“AT89S52 Micro computer”。试分别用查询方式和中断方式编写程序。解：查询方式：#includereg52.hunsigned char a[]={“AT89S52 Micro computer\0”};unsigned char i=0;main (){TMOD=0x20;TH1=0xFA;TL0=0xFA;SCON=0x40;TR1=1;TI=1;while(a[i]!=0){while(TI==0);TI=0;SBUF=a[i];i++;}}中断方式：#includereg52.hunsigned char a[]={“AT89S52 Micro computer/0”};unsigned char i=0;main(){TMOD=0x20;TH1=0xFA;TL0=0xFA;SCON=0x40;EA=1;ES=1;TR1=1;TI=1;while(1);}uart () interruput 4 using 1{if(TI==1){while(a[i]!=0){TI=0;SUBF=a[i];i++;}}}第七章7.4假设外部数据存储器4000H单元的内容为80H，执行下列指令后累加器A中的内容为（80H）MOV P2，#40HMOV R0，#00HMOVX A,@R07.6 编写程序，将外部数据存储器中的4000H~40FFH单元内容清零。ORG 0000HMOV DPTR,#4000HMOV R7,#0FFHMOV A,#00HLOOP:MOVX @DPTR,AINC DPTRDJNZ R7,LOOPSJMP $END7.8 区分MCS-51单片机外程序存储器和片外数据存储器的最可靠方法是（）。答：看其位于地址范围的低端还是高段看其是与RD信号连接还是与PSEN信号连接。第八章8.16 在AT89S52单片机系统中接入一片地址为7FF8H~7FFFH的ADC0809芯片，试画出系统硬件连接图，并编写ADC0809初始化程序和定时采样通道1的程序。#includereg52.h#define uchar unsigned char #define IN1=XBYTE[0x7ff8]uchar xdata *addz;uchar pata adcdata[8];uchar i;void main(){IT1=1;EA=1;EX1=1;i=0;addz= IN1;*addz=i;while(1);}void init1() interrupt 2{adcdata[i]=*addz;i++;addz++;if(i8){*addz=i;}else{EA=0;EX1=0;}}第九章9.2#includereg51.h#includeinstrins.h#define uchar unsigned char#define ulong unsigned longsbit AD_CS=P1^0;sbit AD_CLK=P1^1;sbit AD_DAT=P1^2;bdate uchar addatasbit adin0 = addata^0;void delay(void){ uchar I;for(i=0;i20;i++);}void main(){uchar i;AD_CLK=0;AD_CS=0;_nop_();for(i=0;i8;i++){AD_CLK=1;delay();adin0=!AD_DAT;addata=addata1;AD_CLK=0;}p0=addata;}9.3#include reg51.h#includemath.hsbit S1=p2^0;sbit S2=p2^1;sbit S3=p2^2;sbit S4=p2^3;sbit DA_DIN=p1^0;sbit DA_CLK=p1^1;sbit DA_CS=p1^2;void delay_S(unsigned char n){unsigned char I;for (i=0;in;i++);}void TLC5615_DA_conver(unsigned int DA_data){unsigned char I;DA_data=DA_data2;DA_CS=1;DA_CLK=0;DA_DIN=0DA_CS=0;for (i=0;i16;i++){ DA_data=DA_data1;DA_DIN=CY;DA_CLK=1; delay_s(0x02);DA_CLK=0; delay_s(0x02)}DA_CS=1;delay_s(0x20;);}voi