管座系列(支管台).doc

产品概述连接形式支管台形式有标准型、短管型、斜接型、弯头型，详见下表型式 Type 连接型式(支管台与支管) Connected type 承插焊 GB19326 Socket welded 管螺纹 GB19326 Pipe thread 对焊GB19326 Butt-welded ??标准型 Standard SOL (MSS SP-97、Q/FG11标准) TOL (MSS SP-97、Q/FG12标准) WOL (MSS SP-97、Q/FG13标准) ??短管型 Nipolet SNL (Q/FG/14标准) TNL (Q/FG14、SHB-PO1) WNL (Q/FG14标准) ??斜接型(45o) Latrolet SEL (Q/FG/15标准) TLL (Q/FG15、SHB-PO1) WLL (Q/FG15标准) ??弯头型(1.5D) Elbolet 　 TEL (Q/FG16、SHB-PO1) WEL (Q/FG16标准) 对焊支管台承插焊支管台螺纹支管台短管支管台斜接支管台弯头支管台螺纹支管台参数表执行标准：MSS SP-97、GB19326、Q/FG11支管公称通径Nominal Diameter of Branch 适用主管公称通径Nominal Diameter of Suited Main Pipe 不小于≥ L E DN NPS mm in 3000LB 6000LB 3000LB 6000LB 6 1/8 20 3/4 19.1 - 15.9 - 8 1/4 20 3/4 19.1 - 15.9 - 10 3/8 25 1 20.6 - 19.1 - 15 1/2 32 1.1/4 25.4 31.8 23.8 19.1 20 3/4 40 1.1/2 27.0 36.5 30.2 25.4 25 1 50 2 33.3 39.7 36.5 33.3 32 1.1/4 65 2.1/2 33.3 41.3 44.5 38.1 40 1.1/2 65 2.1/2 34.9 42.9 50.8 49.2 50 2 80 3 38.1 52.4 65.1 69.9 60 2.1/2 100 4 46.0 - 76.2 - 80 3 125 5 50.8 - 93.7 - 100 4 150 6 57.2 - 120.7 - 说明： 1、锥管螺纹可按ANSI B1.20.1 NPT或ISO7/1Rp或Rc锥管螺纹，尺寸同支管公称通径(in)用户需注明锥管螺纹代号。 2、表列“适用主管公称直径”为一般用途，如需用于更小的主管尺寸应与制造厂协商。 3、按下表选用支管台的压力等级： 压力等级Pressure Grade 适用支管壁厚等级Suitable shedule of branch 3000Lb Sch40、 Sch80、? STD、? XS 6000Lb Sch160? XXS 对焊支管台参数表执行标准：MSS SP-97、GB19326、Q/FG13公称通径 Nominal Diameter 适用主管公称通径Nominal Diameter of Suited Main Pipe ≥ L E mm in mm in STD XS XXS STD XS XXS 6 1/8 20 3/4 15.9 - - 15.9 - - 8 1/4 20 3/4 15.9 - - 15.9 - - 10 3/8 25 1 19.1 - - 19.1 - - 15 1/2 32 1.1/4 19.1 19.1 28.6 23.8 23.8 14.3 20 3/4 40 1.1/2 22.2 22.2 31.8 30.2 30.2 19.1 25 1 40 1.1/2 27.0 27.0 38.1 36.5 36.5 25.4 32 1.1/4 65 2.1/2 31.8 31.8 44.5 44.5 44.5 33.3 40 1.1/2 65 2.1/2 33.3 33.3 50.8 50.8 50.8 38.1 50 2 80 3 38.1 38.1 58.6 65.1 65.1 42.9 60 2.1/2 100 4 41.3 41.3 61.9 76.2 76.2 54.0 80 3 125 5 44.5 44.5 73.0 93.7 93.7 77.0 90 3.1/2 150 6 47.0 47.0 - 101.6 101.6 - 100 4 150 6 50.8 50.8 84.1 120.7 120.7 98.4 125 5 200 8 57.2 57.2 93.7 141.3 141.3 122.2 150