缝纫工培训.ppt

New Sewer Training-Phase I新员工缝纫基础培训-1 1. Seam 拼缝 2. Top Stitch 压单针 3. Double Needle 双针 4. Cut off corner 缺口＆Notch刀口 5. Zipper 拉链 6 Welt 滚绳 7 Denim 里布 8 Velcro 粘钩、粘毛 9 Elastic 松紧带 Reinforcement 加强带 11. Pleat *New Sewer Training Module 1 Seam width: 1.2cm 拼缝宽度1.2公分 Stitch length per drawing 根据图纸确定针码 Back tack: Both ends 两头需要倒回针 Seam gauge required: 一定要用拼缝定规  1.2cm 1.2公分 Stitch length per drawing 根据图纸确定针码 2 part join 2块面料拼缝 Instructions 说明： Remark: Different materials and styles require different stitches. 注：此示意图是根据布料要求，实际操作要根据不同款式要求，针码也不同 Seam gauge 定规 Material edge 布料边缘 Back tack 开始与结束倒回针 Standard seam width 1.2 CM+/- 0.2 CM 标准缝头宽度：1.2 CM+/- 0.2 CM √ This seam is too wide （缝头宽） and irregular (v. parallel to edge), x Seam is too narrow （缝头窄） x 0.6cm厘米 Cut off corner 缺口 0.6cm厘米 A B Seam width on face: 0.6cm 压单针0.6公分 Based on the drawing top stitch must be sewn on the requested part (AB). 根据图纸，单针必须压在指定部件上(AB) Instructions说明: Stitch per drawing 针码根据图纸要求 Top stitch 单针压线 Cut off corner 缺口 Seam width must be equal 左右宽窄必须一致 Stitch length per drawing 根据图纸确定针码 Back tack: Both ends 两头需要倒回针 Instructions: Stitch length per drawing 针码根据图纸要求 Cut off corner 缺口 Notches corners must match when joining. 拼缝时，要注意刀口对齐，注意缺口和缺口拼合 Notch 刀口 xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx Zipper slide face to cut off corner side 拉链头的平头对应缺口方向。 Instructions说明: Zipper slide 拉链平头 Zipper 拉链 Welts start from notch 滚绳从刀口开始 Welts 滚绳 Welts must be tight 滚绳要包紧，不能漏线 Instructions说明: Welt cord 滚绳 Welts 滚绳 Denim 里布 Start joining denim from notch 里布从刀口开始拼合 Instructions说明: L81A L=左 left 8=扶手arm A=Arm（扶手） L8 L8 L8 Denim 里布 Start joining denim from notch 里布从刀口开始拼合 Instructions说明: X81A X=右 8=扶手 A=Arm（扶手） 3C Rough Velcro 粘钩 Smooth Velcro 粘毛 Smooth Velcro 粘毛 21S 3=中间坐垫 C=cushion (坐垫) L3=左坐垫 X3=右坐垫 Hook loop must be sewn according to the holes location and cover the holes 粘钩和粘毛位置准确，盖住里布洞眼 Instructions说明: 3C Holes 洞 粘钩 粘毛 Velcro color must match denim 粘钩和粘毛颜色必须与里布一致 Hol