- 1、本文档共10页,可阅读全部内容。
- 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
- 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载。
- 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
ASME 理化检验控制程序 Physiclal and Chemical Test Control Procedure概要1
Physical and Chemical
Test Control Procedure
理化检验控制程序
Effective Date: 2012/06/02
发布日期:2012/06/02 Prepared by
编制 Reviewed by
审核 Reviewed by
审核 Approved by
批准 Title
职位 Physical Test
Engineer
理化测试工程师 Responsible
Physical Test
Engineer
理化测试责任工程师 Responsible
Quality Assurance Engineer
质量保证责任工程师 Manager of
Quality Control Department
质量控制部经理 Signature/Date
签字/日期 1.0 Scope 范围
This procedure applies to the physical and chemical testing control including cutting control of test coupons and specimens in compliance with the requirements of ASME Code Section III. 本程序适用于包括符合ASME规范第3卷测试试件和试样的取样控制要求在内的力学和化学检测质量控制。
2.0 References 参考文件
2.1 ASME Code Section III NCA-Latest Edition and Addenda ASME规范第三卷NCA卷-最新版及其增补
2.2 ASME Code Section III Division 1 Subsection NB-Latest Edition and Addenda ASME规范第三卷第一册NB分卷-最新版及其增补
2.3 XXXX QA Manual Section 8 and 11-Latest Edition and Revision XX公司质量保证手册第8卷和11卷-最新版本及修订
2.4 Inspection and Test Personnel Qualification Procedure(XXXX/MP-ASME-10)- Latest Revision检查和试验人员资格审查程序(XXXX/MP-ASME-10)-最新修订
2.5 Measuring and Test Equipment Control Procedure(XXXX/MP-ASME-34)- Latest Revision测量和试验设备控制程序(XXXX/MP-ASME-34)-最新修订
3.0 Definition and Abbreviation 定义和缩写
3.1 QP: Quality Plan;QP 质量计划
3.2 Coupon: a portion cutting from the product for preparation of specimen;试件:从产品上切取下来为制备试样做准备的一部分。
3.3 Specimen: the standard sample for test after the coupon is machined in accordance with applicable Codes, standards, and technical requirements.试样:试件依照适用的法规,标准和技术要求进行加工后的用于测试的标准样品
4.0 Responsibilities and Authorities职责和权限
4.1 The Machining Inspector shall be responsible for the machining and inspection control of specimen according to Sampling Instruction.质量检查员负责依照试样加工指导书对试样加工和检查进行控制。
4.2 The Responsible Physical/Chemical Test Engineer shall be responsible for the control of the physical, metallographical and chemical test.理化责任工程师负责材料的力学、金相和化学测试
5.0 General Requirement 一般要求
5.1 Related specimen shall be prepared in accordance with
您可能关注的文档
- arduino学习笔记概要1.doc
- 冷拼与雕刻专业实验报告概要1.doc
- 冷战史研究概要1.ppt
- arena仿真详细教程概要1.doc
- 冷箱吊装方案概要1.doc
- 冶金认识实习报告概要1.doc
- Are_you_feeling_bored_教学课件概要1.ppt
- Are you washing clothes 新课标1级 B Lesson 7第一课时概要1.ppt
- Are you washing clothes 新课标1级B Lesson 7第二课时概要1.ppt
- Are_you_feeling_bored?课件 [兼容模式] [修复的]概要1.ppt
- 10《那一年,面包飘香》教案.docx
- 13 花钟 教学设计-2023-2024学年三年级下册语文统编版.docx
- 2024-2025学年中职学校心理健康教育与霸凌预防的设计.docx
- 2024-2025学年中职生反思与行动的反霸凌教学设计.docx
- 2023-2024学年人教版小学数学一年级上册5.docx
- 4.1.1 线段、射线、直线 教学设计 2024-2025学年北师大版七年级数学上册.docx
- 川教版(2024)三年级上册 2.2在线导航选路线 教案.docx
- Unit 8 Dolls (教学设计)-2024-2025学年译林版(三起)英语四年级上册.docx
- 高一上学期体育与健康人教版 “贪吃蛇”耐久跑 教案.docx
- 第1课时 亿以内数的认识(教学设计)-2024-2025学年四年级上册数学人教版.docx
文档评论(0)