机械设计技术要求大全（Mechanical design technical requirements）.docVIP

下载本文档

9
0
约1.02万字
约 10页
2017-07-22 发布于河南
举报
版权申诉

机械设计技术要求大全（Mechanical design technical requirements）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

机械设计技术要求大全（Mechanical design technical requirements）

机械设计技术要求大全（Mechanical design technical requirements） Mechanical design technical requirements 2007-04-25 14:45:03 Small and medium-sized Tags: mechanical design, technical requirements (today encountered a difficult problem, let me write a casting technical requirements, thanks to I also learned a bit mechanical design, in the Internet search a, mechanical design technical requirements Daquan, here shared) 1. parts remove oxide skin. 2. parts processing surface should not have scratches, scratches and other parts of the damaged surface defects. 3. deburring edges. 4. by quenching and tempering treatment, HRC50 ~ 55. 5. parts are subjected to high frequency quenching, tempering at 350~370 DEG C, HRC40 ~ 45. 6. carburizing depth 0.3mm. 7. high temperature aging treatment. 8. no injection form tolerances shall comply with the requirements of GB1184-80. 9. no injection length dimension allowable deviation + 0.5mm. 10. the tolerance zone of casting is symmetrical to the basic dimension of rough casting. 11. no fillet radius R5. 12. no injection chamfer is 2 x 45 degrees. 13. acute angle blunt. 14. the seals must be soaked before they are assembled. 15. rolling bearings are allowed to be heated by oil heating. The temperature of the oil shall not exceed 100 degrees. 20. after the gear assembly, the tooth surface contact spot and the backlash should conform to the GB10095 and GB11365 stipulation. 21. sealing filler or sealant shall be allowed for assembly of hydraulic systems but shall be prevented from entering the system. 22. assembly parts and components (including purchased parts, outsourcing parts) must have the certificate of inspection department before they can be assembled. 23. parts must be cleaned and cleaned before assembly. There shall be no burrs, edges, skins, rust, chips, oil stains, stains and dust. 24. before assembly, the main Coordination dimensions of the parts, especially the interference fit size and the relative accuracy shall be reviewed. 25. assem