交流接触器测试方法-B2B99_Com（Testing method of AC contactor -B2B99_Com）.docVIP

下载本文档

6
0
约 15页
2017-07-22 发布于河南
举报
版权申诉

交流接触器测试方法-B2B99_Com（Testing method of AC contactor -B2B99_Com）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

交流接触器测试方法-B2B99_Com（Testing method of AC contactor -B2B99_Com）

交流接触器测试方法-B2B99_Com（Testing method of AC contactor -B2B99_Com） Testing method of AC contactor 1 test conditions 1.1 the sample shall conform to the drawings and technical documents approved by the prescribed procedures. 1.2 each test item shall be carried out on a new electrical apparatus which matches the applicable and typical AC contactor. Without affecting its equivalence, some test items may be allowed to be tested on the same sample. 1.3 before the test, operate the electric appliance several times in the no-load or load condition. 1.4 test tolerance Except as specified in the test method, the allowable error of the test parameters shall be as follows: Voltage: 5%; Power factor: 0.05; Current: 5%; Under the premise of the manufacturers approval, it is equally effective for the convenience of the test and the test parameters and test methods more stringent than those prescribed. 2 verify structural requirements 2.1 marking inspection and marking durability test Check whether the contents of nameplates, labels and relevant technical documents and marks meet the requirements of the fifth chapter. Mark on the casing or nameplate of the appliance, hand in a piece of absorbent cotton soaked in distilled water, rub it 15 times in about 15 s, and then use a piece of skim cotton soaked in gasoline at about 15 Within 15 times of the s, the logo should be easy to recognize. The marking made by means of coining and pressing can not be carried out in this test. The markings on the enclosure or nameplate shall be readily identifiable without any warpage after all tests as specified in this standard. 2.2 humidity resistance test This experiment adopts the Db test method, and the requirements of the test case are stipulated in GB/T 2423.41993 and second chapters. During test, the sample should be installed in normal working position. The test conditions shall be carried out according to the strict grade stipulated in 7.1.1.1 and the requirements of GB/T 2423.41993 and fifth c