pc dims 测头文件编辑指南（PC dims header file editing Guide）.docVIP

下载本文档

61
0
约6.25千字
约 8页
2017-07-23 发布于河南
举报
版权申诉

pc dims 测头文件编辑指南（PC dims header file editing Guide）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

pc dims 测头文件编辑指南（PC dims header file editing Guide）

pc dims 测头文件编辑指南（PC dims header file editing Guide） PC-DMIS header file editing Guide V1.0 The probe.dat file in the root of the PC-DMIS software determines the graphical display and data representation of the PC-DMIS probe system. If you want to use probes in PC-DMIS, you need to define them in the probe.dat file. You can use the Windows Notepad to open this file for definition and editing. The definition of the probe has particular formatting requirements and must be strictly observed. Lets introduce... Main expression method: Commands: ITEM: Begintip Endtip Ribcount Line Sphere Cutsphere Cylinder Cone Ring Comment Hotspot Opticalcenter Connect Autojoint Manualjoint Face Solid Cadgeom These commands are described below: ITEMIP2BY20MM M2, the first name that appears after the first line ITEM, Will appear in the probe Definition dialog box, The following M2 defines the thread type of this part Or connection type. Begintip needle definition begins. Endtip needle definition end. Ribcount N N stands for rows, 2 to 1000. Line x1, Y1, Z1, X2, Y2, Z2, x1, Y1, Z1, Z2 is the starting point, X2, Y2, and is the end point Sphere X Y Z D x, Y Z, said the center coordinates, D diameter. Cutsphere, x, y, Z, I, J, K, D, B, t, x, y, Z, and d represent the same content as sphere, I, J, and K represent vectors perpendicular to the top and bottom of the ball. T, B defines the top and bottom positions as follows: Top = = (x, y, z) + T * (I, J, K) Bottom = = (x, y, z) - B * (I, J, K) Cylinder X1 Y1 Z1 x2 Y2 Z2 D x1, Y1 Z1, said the top of the cylinder position X2, Y2 Z2, said the bottom surface of the cylinder position D diameter. Cone x1, Y1, Z1, D1, X2, Y2, Z2, D2, x1, Y1, Z2, Z1 represents the position of the cone top, X2, Y2, and the position of the cone base, D1 represents the diameter of the top surface, D2, which represents the diameter of the underside. Ring X1 Y1 Z1 I1 J1 K1 D1 D2 x1, Y1 Z1, said the ring center coordinates I1, J1, K1 relative to the current measuring ring vec