西门子变频器使用手册（SIEMENS frequency converter manual）.docVIP

下载本文档

71
0
约9.38千字
约 13页
2017-07-24 发布于河南
举报
版权申诉

西门子变频器使用手册（SIEMENS frequency converter manual）.doc

1、本文档共13页，可阅读全部内容。
2、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。
3、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
5、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
6、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
7、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
8、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

西门子变频器使用手册（SIEMENS frequency converter manual）

西门子变频器使用手册（SIEMENS frequency converter manual） 3.2 debugging method 3.2 debugging method IMICROMASTER 420 inverter in standard supply mode, fashion has status display board (SDP) (refer to figure 3-2), for For multiple users, the inverter can be successfully put into operation with the default settings of the SDP and the manufacturer. If the factory The default setting value is not suitable for your device. You can use the basic operating board (BOP) (see Figure 3-2) or the advanced operating panel (AOP) (see Figure 3-2) modify the parameters to match them. BOP and AOP are available as options. You can too Use the PC IBN tool Drive Monitor or STARTER to adjust the factory settings. The associated software is in tune with frequency conversion Supplied in CD ROM can be found. Status display board, basic operating board, advanced operation board Figure 3-2 operation panel for MICROMASTER 420 inverter For the steps to change / replace the operation panel, see the relevant appendices in this manual. Prompt The default power frequency setting value (factory setting value) can be changed using the DIP switch under SDP; the setting of the converter delivery As follows: DIP switch 2: Off position?: Default values for Europe (50 Hz, power unit: kW) On position?: Default values for North America (60 Hz, power unit: HP) DIP switch 1: Not for user use. 3.2.1 is debugged and operated using the status display panel (SDP) 3.2.1 is debugged and operated using the status display panel (SDP) The SDP on the panel has two LED for displaying the current running state of the inverter (see Section 6.1). When SDP is adopted, the preset value of the converter must be compatible with the following motor data: Motor rated power Motor voltage Motor rated current Motor rated frequency (it is recommended to use SIEMENS Standard Motors) In addition, the following conditions must be satisfied: Linear V/f motor speed control, analog potentiometer input. 50 Hz power supply, the maximum speed is 3000