高级管道工理论知识试卷（Senior plumbing theoretical knowledge test）.docVIP

下载本文档

10
0
约2.11万字
约 26页
2017-08-04 发布于河南
举报
版权申诉

高级管道工理论知识试卷（Senior plumbing theoretical knowledge test）.doc

1、本文档共26页，可阅读全部内容。
2、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。
3、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
5、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
6、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
7、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
8、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

高级管道工理论知识试卷（Senior plumbing theoretical knowledge test） Senior plumbing theoretical knowledge test (H-2) objective test part of the answer. Choice question Hydraulic pipe bender is generally used for bending diameter of not more than mm (A). A.44.5 B. 45. 5 C. 46. 5 D. 47. Five The bending radius of hot bending bend should not be less than the outer diameter of the times (A) A.3.5 B. 4 C. 4. 5 D. Five The use of electric pipe bending machine, when the bending is larger than the outer diameter of pipes (C) mm must be placed in the tube bending mandrel. A.80 B. 70 C. 60 D. Fifty The general provisions of pipe bending, tube wall thinning rate shall not exceed (C) A.5% B. 8% C. 15% D. 20% When the temperature changes of the steel tube (T) less than (B), can not be considered compensation. A.300C B. 320C C. 340C D. 360C The pre tension waveform expansion device, the tension deviation not more than mm (A). A.5 B. 10 C. 15 D. Twenty The waveform expansion device lining one end of the sleeve and the other end can be wave wall welding (C) A. fixed B. Fixed C welding. Free mobile D. Fixed thread In the square lifting telescopic device, tension deviation should be less than mm (B). A. + 5 B. + 10 C. + 15 C. + 20 There are different flow and adapt to economic flow diameter, the diameter of the flow (A) A. diameter B. Economic flow C. Nominal diameter D. nominal flow In the network in order to prevent water hammer damage caused, for maximum flow rate (C) A.0.5-0.7m/S B. 1-1. 6m/S C. 2. 5-3m/S D.3-3.6m/S For gas, hydrogen, low pressure air pipe, the general pressure gauge (B). A. spring tube B. Diaphragm type C. Acetylene type D. Oxygen type The rotor flowmeter is suitable for the pressure is not more than (B) pipeline. A.0.098Mpa B1. 96Mpa C. 5. 88Mpa D. 6. 3Mpa Tube pressure gauge should be set at ambient temperature is in the form of U (C) within the scope of the place. A.10-500C B. 15-600C C. 10-600C D. 20-600C Bourdon tube pressure gauge pipeline pressure fluctuations in the