TCL维修实例逐个记（TCL maintenance instance is recorded one by one）.docVIP

下载本文档

4
0
约2.81万字
约 27页
2017-08-04 发布于河南
举报
版权申诉

TCL维修实例逐个记（TCL maintenance instance is recorded one by one）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

TCL维修实例逐个记（TCL maintenance instance is recorded one by one） TCL maintenance instance is recorded one by one TCL rc - c08 sometimes show voltage 250 v, sometimes suddenly show voltage power grid voltage below 130 v R874 automatic shutdown system voltage detection circuit (120 k), open circuit or C853 one feet away welding (into the bus adjust AC - VOL - LOW after a 32 original data transferred to the 15 is ok. This seems to be LOW voltage detection voltage control point. The other AC - VOL - HIGH is a voltage detection of HIGH and LOW voltage control point.) The TCL2980DB D828 D828 D828 D828 D828 D828 D828 D828 is not good for the standby 20V, the secondary boot protection is 0, and the voltage of the tube is not normal using the 15K resistance. The tcl2918e switch machine problem prescription 1. + B capacitance and glue 2. R831 (1.5k) is common in the automatic shutdown of these two components with sealant, should be removed. 3, R836 R832 4, 2.5 V CPU18 feet 5, 70 V rectifier diode Users said 2918 e if a machine to shut down the ac power after a certain period of time is difficult to the secondary boot, a large number of open unchanged after welding repair welding, practices 30 V output power fluctuation, 12 V + 70 actual fluctuation change data cant boot, + 5 V wave, measuring the output waveform of all stripes, normal ac 400 V waveform is normal, the STR - the power supply voltage regulator tube F6656 Q801 C a waveform in the high frequency component is too big, in 200 after v10uf C808 power fluctuations dont still cannot boot, in touch a continues in crystal remains the same, the measurement of 17 feet reset voltage 5 V, 12 feet power voltage 5 V normal, 18 feet 2.5 V normal, rewrite the data after troubleshooting, maybe even the user clear machines has been completely damaged, cause there is no doubt the data directly. TCL trump NT21228 color TV irregular automatic stop (in fact more than the city voltage is too high 开机观察,发现停机后等几分钟再开机又正常了,但时间越来越短,开机后电视机不自动关机如果人为