大型颚式破碎机主轴承更换修理工艺（Replacement and repair of main bearing of large jaw crusher）.docVIP

下载本文档

2
0
约7.86千字
约 6页
2017-08-04 发布于河南
举报
版权申诉

大型颚式破碎机主轴承更换修理工艺（Replacement and repair of main bearing of large jaw crusher）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

大型颚式破碎机主轴承更换修理工艺（Replacement and repair of main bearing of large jaw crusher） The main bearing large jaw crusher are mostly used to open the sliding bearing, the bearing lining is mostly made of Babbitt, bearing the scraping technology higher, scraping is not good or improper gap, will lead to research or tile burning accident. We have summarized a set of tiles for good scraping and clearance adjustment methods are presented below for your reference. 1 demolition of the old watt hour should do (1) measuring the old bearing joint surface wakou the thickness of the gasket. (2) measurement of the main level. (3) carefully check whether the spindle smooth, if there is rust scratches and other defects, such as should be avoided. (4) top clearance, side gap and old bearing axial clearance measurement. 2 detection of tile back and the bearing contact According to the general technical conditions of JB/T5000.10-1998 heavy machinery requirements, must be tile back scraping, make it meet technical requirements. Otherwise, when the equipment running between the bearing and the bearing seat are prone to slip or reverse rotation. In order to prevent this phenomenon, generally uses the pin and sleeve type positioning method, as described in this paper is the main bearing is provided with a locating pin. 3 Bush scraping techniques According to the general technical conditions in the JB/T5000.10-1998 heavy machinery assembly requirements, spindle scraping should meet the following technical standards. (1) spindle and the bearing is fine and uniform contact, and the gap with the outside of the upper and lower bearings and spindle contact angle part of the formation of oil wedge and wedge wakou, from starting from the maximum gradually transition to zero. (2) the contact angle is not too big nor too small. The contact angle is too small, can make the bearing pressure increases, which will make the bearing deformation, accelerated wear, shorten the service life; the contact angle is t