二次开粗方法的比较和选择（Comparison and selection of two opening methods）.docVIP

下载本文档

1
0
约1.92万字
约 17页
2017-08-20 发布于河南
举报
版权申诉

二次开粗方法的比较和选择（Comparison and selection of two opening methods）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

二次开粗方法的比较和选择（Comparison and selection of two opening methods）

二次开粗方法的比较和选择（Comparison and selection of two opening methods） Comparison and selection of.Txt two rough methods of Ming Sao is easy to hide, dark base to prevent. Buddha said: you two are silly, B!! When the night is turned on the bed again, the sun is born, and the comparison and choice of the two opening methods are made Selection A lot of friends are confused about the choice of the two rough method, and I sum up according to my experience and understanding. Two rough general including conventional method and non conventional methods, such as conventional use 3D, unconventional pruning, we can according to the characteristics of the parts and personal habits and experience to choose the most reasonable way. Here are some main general ways for your reference. 3D uses IPW for two coarse features: 1, knife rail calculation time is long; 2, may produce more empty knife; 3, there is a correlation with the upper process, and if the previous process changes, then the current operation must be re generated calculation. Use layer based IPW for two boot features: 1, the calculation time of tool path is less than 3D; 2, the generated cutter path is more regular than the 3D cutter path; 3. Cutting corners and stepped surfaces in previous operations can be efficiently cut; 4, you can use a larger tool in the rough machining to complete a deep cut, and then in the following operation, the same tool to complete a very shallow cutting, to clear the ladder surface. Use reference tool for two times to open rough features: 1, the calculation time of tool rail is reduced by two times with IWP; 2. Machining only the corner area of the remaining material; 3. Select the diameter of the reference tool must be greater than the diameter of the tool used in the previous process. 4, there is no correlation with the upper process, so it is easy to edit and modify the cutting parameters. The use of reference tool two times thick, only cutting the corner area of the remaining material, fast ca