袋笼焊机说明书.doc

DLN系列袋笼焊机 DLN Series Bag Cage Welding Machine 使用说明书 Operation Manual （第5代） 浙工数控焊机有限公司 制造 浙江省嘉兴市城南路科创中心（公司、销售、研发）0573浙江省嘉兴市新塍兴园路（厂区） 057383528660 安全1.Safety 必须按照如下安全规则进行操作，否则可能造成人身伤害和设备损坏 Operation must be done according to the following safety rules, otherwise it may hurt people or damage equipment 焊机必须由专职电工和设备安装人员进行安装、调试、修理。 Installation, commissioning and repair of welding machine shall be done by skilled electrician and equipment installing personnel. 焊机必须可靠接地，接地电阻小于10欧姆，接地线为不小于16平方毫米的铜线 Welding machine must be safely grounded. Grounding current resistance shall be less than 10Ω. Diameter of grounding copper wire shall not be less than 16 square mm. 进行焊机调整、维修时必须切断电源，并拆除电源进线 Adjustment and maintenance of welding machine must be done when it is powered off and the incoming power wire is removed. 焊机不带电源开关，用户应在电源的输入线路接100安的空气开关 The welding machine is not equipped with switch. User must connect a 100A air switch on the incoming power wire. 操作人员必须经过培训才可操作该设备 Only trained operating personnel can operate this equipment. 当手伸入电极工作区域时，切勿踩下脚踏开关，否则手可能会被电极夹伤 Don’t press on foot switch when hands move into electrode working area, otherwise, hands may be hurt by electrode. 为防止焊接火花伤及人眼及皮肤，操作时必须带护目眼镜 Take on protective glasses while operating to prevent welding sparks from hurting eyes or skin. 如发现焊机有漏电的嫌疑，必须立即停止使用并切断电源，请专职电工进行维修，或通知本公司派人修理 In the event of any sign of creepage, operation must be stopped and power supply must be switched off immediately. Ask skilled electrian to repair, or inform our company for repair. 焊接后的工件会烫手，操作工应戴好手套 Wear gloves. Caution welded parts hurt. 概述Brief introduction 袋笼的焊接基本技术要求Basic technical requirement for welding bag cage 焊点的强度当受外力冲击时，焊点牢固、不脱落。应符合中华人民共和国机械行业标准《袋式除尘器用滤袋框架》JB/5917-1991第 5.3条。 焊点处毛刺毛刺短且少，不能刮伤滤袋。应符合中华人民共和国机械行业标准《袋式除尘器用滤袋框架》JB/5917-1991第 5.4条 。 直线度直线度高。垂直度公差应取负公差。应≤框架长度的2‰。 袋笼焊机的基本技术要求 袋笼焊机应能保证所焊接的袋笼，具有焊点牢固、毛刺少、直线度高的要求。 1、3 DLN系列袋笼焊机的基本型号及主要特点 A、型号 名称 型号 变压器数量 每拍动作所焊点数 焊接每个环筋所需时间（含推出袋笼的