determination of the optimal speed of pultrusion for large-sized composite rods确定最优的拉挤速度大型复合棒.pdfVIP

下载本文档

1
0
约 6页
2017-08-28 发布于上海
举报
版权申诉

determination of the optimal speed of pultrusion for large-sized composite rods确定最优的拉挤速度大型复合棒.pdf

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

determination of the optimal speed of pultrusion for large-sized composite rods确定最优的拉挤速度大型复合棒

Journal of Encapsulation and Adsorption Sciences, 2012, 2, 21-26 / 10.4236/jeas.2012.23004 Published Online September 2012 (http://www.SciRP.org/journal/jeas) Determination of the Optimal Speed of Pultrusion for Large-Sized Composite Rods Aleksandr Krasnovskii, Iliya Kazakov Department of Composite Materials, Moscow State Technological University “STANKIN”, Moscow, Russia Email: al.krasnov@mail.ru, kazakov_iliya@mail.ru Received June 18, 2012; revised July 20, 2012; accepted August 6, 2012 ABSTRACT The paper describes a mathematical model of the stress-strain state of polymer composite materials in the pultrusion process of large-sized products. The influence of the pull speed on the stress-strain state of the products is investigated. To determine the maximum possible pull speed series of solutions at different pull speeds are obtained. Depending on the maximum strain in the cross section of the rod determined the optimal value of pulling speed. Keywords: Composite Material; Pultrusion; Stress-Strain State; Permeability; Oversized Rod 1. Introduction the liquid resin and chemical shrinkage are effects on the value of strain. Pultrusion is one of the most common ways to manufac- ture large products made of polymer composites. The 3. Stress-Strain State Model possibilities to improve the performance of pultruded products depending on the reinforcement scheme are well Consider the section A-A of the rod consisting of two studied [1-4]. The influence of constructive and techno- regions (Figure 2(а)). logical parameters of pultrusion process on the properties of the