隐适美-技师沟通模版.docxVIP

隐适美技师沟通参考模版一、处方表中“特殊说明”1 写明治疗目标和特殊主诉要求：Treatment objective: Aim at2 终末状态：End result:1）中线：Midline：2）尖牙磨牙关系：Canine and molar relationship:3）覆合及覆盖：Overbite and overjet:4）切牙位置及转矩：Incisors position and angulation:3上下颌间隙来源：唇倾、扩弓、IPR、推磨牙向后、拔牙、后牙去扭转等1）上颌：Upper:2）下颌：Lower:4 步骤：Staging：5其他牵引钩及开窗：Hook and cutout:开展间隙：Space:个人偏好：如后牙紧密咬合接触Posterior heavy contact6若PVS咬合记录连同印模同时寄出，需在特殊说明中标注:请扫描并根据PVS咬合记录建立咬合关系Please scan PVS bite record and set initial bite according to it二、中线1维持上中线，以上中线为准，下中线对齐上中线Maintain upper midline, coordinate lower midline with upper2上中线向左/右移动1mm，下中线对齐上中线Shift upper midline to the left/ right side by 1mm, coordinate lower midline with upper*切勿出现：1 对齐中线；2 口内中线对齐面中线三、下切牙位置、转矩1 维持4.1位置，排齐下切牙Maintain position of 4.1, align other incisors with 4.12 下前牙唇倾/内收1mmProcline/Retract lower anterior by 1mm3 维持3.1转矩，其他切牙与之匹配Maintain torque of 3.1, match other incisors’ crown torque with 3.14 在下颌2-2内收时增加10度根舌向转矩Add 10 degree root lingual torque to lower 2-2when retracting them四、上切牙位置（覆盖）、转矩1 以1.1为准排齐上切牙Align upper incisors with the initial 1.12 上前牙内收3mmRetract upper anterior by 3mm3 达到前牙0.5mm覆盖，必要时辅助IPRAchieve 0.5mm OJ, add IPR on upper anterior as needed4 维持1.1转矩，其他切牙与之匹配Maintain initial torque of 1.1, match other incisors’ crown torque with 1.1五、覆合1下颌3-3压低1.5mmIntrude lower 3-3 by 1.5mm2 压低下前牙整平Spee 曲线Intrude lower anterior to achieve 0 degree curve of Spee3 压低下前牙至0.5mm覆合Intrude lower anterior to achieve 0.5mm OB六、磨牙关系及位置1 上颌磨牙不要前移Donot mesialize upper molars2 通过上颌推磨牙向后达到磨牙I类关系Distalize molar to achieve molar CI relationship3 上颌后牙前移1mmMesialize upper posterior by 1mm4 上颌双侧推磨牙向后3mmDistalize upper left and right molar by 3mm5 上颌后牙前移达到磨牙完全远中关系Mesialize upper molar to achieve molar full Class II relationship七、关闭间隙1 通过前牙内收关闭所有间隙Closeall space by anterior retraction2下前牙内收达到尖牙I类关系，剩余间隙由后牙前移关闭Retract lower anterior to achieve Canine CI relationship, close residual space by posterior mesialization八、开展间隙1 通过3.7后移，在3.6位置开展8.5mm间隙作后期修复Achieve 8.5mm space for 3.6 restoration by 3.7 di