铰孔质量控制探讨（Discussion on reaming quality control）.docVIP

下载本文档

0
0
约1.07万字
约 8页
2017-09-01 发布于河南
举报
版权申诉

铰孔质量控制探讨（Discussion on reaming quality control）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

铰孔质量控制探讨（Discussion on reaming quality control）

铰孔质量控制探讨（Discussion on reaming quality control） To explore the reaming quality control Source: China paper Download Center [08-11-25 10:32:00] author: Cai Jianxin editor: studa20 Abstract according to the analysis on the main factors affecting the quality of reaming, combined with its own experience, puts forward the control in the process of reaming Reaming quality. I think it is very helpful to improve the quality of reaming, has important significance in practice. In Keywords reamer reaming amount of surface roughness of machining quality of the In machining process, often encounter reaming. Reaming is one of the commonly used methods of finishing hole. Because the tooth number of reamer, good performance oriented, the core of the large diameter, good tool rigidity, small machining allowance, cutting thickness of thin, can be IT9 ~ IT7 diameter size precision, surface roughness of the hole can be controlled between Ra1.6 ~ 0.8 M. But in the actual production, reaming quality cannot reach the ideal requirements. The author is how to control the reaming quality following discussion. The A, main factors affecting the quality of reaming (a) the geometric parameters of reamer. Reaming quality depends on the accuracy of reamer and surface roughness. Therefore, a reasonable choice of reamer geometric parameters, determines the reaming quality. One is the reamer diameter. It is decided according to the expansion or shrinkage hole is the nominal dimensions and tolerances and the reaming process is the processing hole. Two is the number of teeth of the reamer. In general, the number of teeth of reamer reaming, the higher the accuracy, the surface roughness value is lower, at the same time, the distribution in each of the cutting edge load is small, to reduce the wear of reamers. But the number of teeth increased but decreased the strength of the cutter teeth, reducing groove. When cutting, the chip is not easy to discharge. Especially deep hole machining and hinge, because