如何写模具毕业设计8板(框)类制品叠层式注射模具设计(论文).docVIP

　　如何写模具毕业设计8板(框)类制品叠层式注射模具设计(论文) 如何写模具毕业设计8板(框)类制品叠层式注射模具设计(论文) 导读：模具毕业设计8板(框)类制品叠层式注射模具设计(论文) 图书分类号： 密 级： 毕业设计(论文) 板(框)类制品叠层式注射模具设计 DESIGN OF STACK INJECTION MOULD PRODUCTS FOR FRAME 学生姓名 学院名称 专业名称 指导教师 机械设计制造及其自动化 年 月 日 摘要 本论文设计了仪器外壳的叠层式热流道模具结构。该模具有2层，每层8个型腔，一次可成型16个产品，该模具是普通注射成型产量的2倍，大大提高生产力。本次模具设计采用的是无流道凝料浇筑系统，不考虑浇道的凝料脱出，减少了分型面，并缩短了成型周期，降低了整个生产成本。而且还采用了齿轮齿条开模机构，在确保俩层型腔同时开模又比较经济。使热流道板的热胀变形问题和浇口的平衡问题有一个很好的解决，基本确保同时充模和充模的稳定可靠性。该模具还采用闭合式喷嘴和闭合式主流道杯，解决了浇口和主流道始端的流涎问题，它采用热电偶控制喷嘴温度和流道板温度。在设计中，为减少热传导热损失。在流道板和型腔板之间采用空气隔热，并加隔热垫，从而降低模具和流道板之间的接触面积，并发挥了支撑热流道板的作用。喷嘴和主流道杯均采用隔热套隔热。 关键词 热流道；叠层式模具；浇口平衡；防流涎 I Abstract This design introduces the mould structure of instrument of outer cover, al current dishes. The mould has 2 layers of types, 8 for each layer, ould can produce 2 times of products ordinary inject shaping, and it boosts productivity greatly . The mould uses a thermal current dish of congeal material , aterial, ould ic adopts a gear and rack to turn on , making sure the two types of 3 4 5 6 7 8 9 10 如何写模具毕业设计8板(框)类制品叠层式注射模具设计(论文) 导读：模具毕业设计8板(框)类制品叠层式注射模具设计(论文)the mould turning on at the same time. The mould gives a good settlement of the expansion problem of the board of the thermal current dishes and the balance problem of runner, guaranting to fill the mould steadily and basically making sure the mould filling at the same time. The mould adopts the spray nozzle of closing type and the cup of mainstream dishes, solve the saliva problem of runner and the top shed of mainstream dishes, and it adopts the electric thermocouple to control the temperature of the spray nozzle and the floould board, there is air to against heat, there are against heat cushions to against heat ,ould board and the floal current. The spray nozzles and the cup of the mainstream dishes have heat insulation set. Keyal current one One pile of types mould Balance the runner Prevent saliva flows II 徐州工程学院毕业设计(论文) 目 录 摘要 ...............................................