蒸汽管道水击简介.ppt

蒸汽管路水击简介 蒸汽管路水击简介 蒸汽管路水击简介 蒸汽管路水击简介 蒸汽管路水击简介 蒸汽管路水击简介 蒸汽管路水击简介 蒸汽管路水击简介 Now that the line is drained, steam can be introduced to warm the line. 蒸汽管路水击简介 蒸汽管路水击简介 蒸汽管路水击简介 蒸汽管路水击简介 Once the line is has been heated for the designated time, the line can be placed back in service. 蒸汽管路水击简介 蒸汽管路水击简介 蒸汽管路水击简介 蒸汽管路水击简介 蒸汽管路水击简介 蒸汽管路水击简介 蒸汽管路水击简介 蒸汽管道内水击的原因： 在送汽前未进行疏水和暖管。 送汽时主汽阀开启过快或过大。 锅炉负荷增加过急或发生满水、汽水共腾等事故，蒸汽严重带水进入管道。 蒸汽管路水击简介 蒸汽管道内水击的处理： 开启过热器集箱和蒸汽管道上的疏水阀，进行疏水。 锅筒水位过高时，应适当排污，保持正常水位。 加强水处理工作，保证给水和锅水质量，避免汽水共腾。 蒸汽管路水击简介 To所 PPE是我们最后一道保护防线。 工作之前确保良好的准备，所有的烧伤和烫伤都是可以避免的。 温馨提示： * * * 蒸汽管路水击简介 蒸汽管路水击简介 蒸汽管路水击简介 蒸汽管路水击简介 蒸汽管路水击简介 蒸汽管路水击简介 蒸汽管路水击简介 蒸汽管路水击简介 蒸汽管路水击简介 蒸汽管路水击简介 蒸汽管路水击简介 蒸汽管路水击简介 蒸汽管路水击简介 蒸汽管路水击简介 蒸汽管路水击简介 蒸汽管路水击简介 First, check and see if the line has sub-cooled condensate. This is best done by using a temperature gun. If the bottom of the line is more than 40°F cooler than the steam, you have sub-cooled condensate. Next, since the magnitude of condensation-induced water hammer is directly related to the difference in up-stream pressure and the vacuum created by the sub-cooled condensate, we need to reduce this differential pressure. So how do you remove the condensate from the lower leg without water hammer? Also, with the steam isolated from the line, the vapor space left when draining the sucondensate will pull air from the atmosphere. The steam contacting sub-cooled condensate is the cause of the water hammer. With air taking the place of the steam, this driving force is eliminated. In other words, isolating the line from the steam header and depressuring it to the atmosphere will reduce the diffierential pressure to almost zero. 蒸汽管路水击简介 蒸汽管路水击简介 蒸汽管路水击简介 蒸汽管路水击简介 蒸汽管路水击简介 蒸汽管路水击简介 Next, open a bleeder at the highest point of the line to depressure line. 蒸汽管路水击简介 蒸汽管路水击简介 蒸汽管路水击简介 蒸汽管路水击简介 蒸汽管路水击简介 蒸汽管路水击简介 Now that the line is about 0 psig, if a vacuum is formed by the contact of sub-cooled condensate and steam, the strength of any water hammer will be