51-的简单c程序.docxVIP

/*程序功能：点亮四个发光二极管 仿真功能：仿真使用8个共阴极数码管，当给P2的高4位置1；低4位置0时，根据二极管的单向导电性，高4位点亮而低4位不亮*/#includereg51.hvoid main(){ P2=0xf0; //给P2口的高4位送1}/*程序功能：利用while语句实现4组发光二极管同时亮和灭*/#include reg51.hvoid main(){int i=100;while(1){while(i--){P0=0xff;P1=0xff;P2=0xff;P3=0xff;}while(i--){P0=0x00;P1=0x00;P2=0x00;P3=0x00;}}}/*程序功能：让共阴极数码管循环显示从0到F*/#includereg52.h //头文件#define uchar unsigned charvoid delay(unsigned int z) // 延时子函数，用于0到F间的变化间隔的调整{unsigned int x, y;for(x=z;x0;x--)for(y=120;y0;y--);}void main()//主函数{while(1) {uchar code LED[]={0x3f,0x06,0x5b,0x4f, 0x66,0x6d,0x7d,0x07, 0x7f,0x6f,0x77,0x7c, 0x39,0x5e,0x79,0x71}; //共阴极数码管，从0到Fint num=0;for(num=0;num16;num++)//循环显示0到F{P1=LED[num];delay(300);}}}/*程序功能：共阴极数码管从0~99循环显示*/#include reg51.h //头文件#define uint unsigned int #define uchar unsigned charsbit wela1=P2^0;sbit wela2=P2^1;uchar code table[10]={0x3f,0x06,0x5b,0x4f,0x66, 0x6d,0x7d,0x07,0x7f,0x6f}; //共阴极数码管数组uint ge,shi;//定义个位和十位uint x,y;void delay(uint z) //延时函数{for(x=z;x0;x--) for(y=110;y0;y--);}void display(uint ge,uint shi) //数码管显示函数{wela1=0;P1=table[shi];//显示十位delay(50);wela1=1;wela2=0;P1=table[ge];//显示个位delay(50);wela2=1;}void main(){int i;for(i=0;i=99;i++) //定义变量i，并使其从0开始不断递增1，一直增加到99{ge=i%10; //取出个位数shi=i/10; //取出十位数display(ge,shi);//调用数码管显示函数delay(10);}} #include reg52.h#define uint unsigned intvoid main(){uint key;P1=0xff;//读P1口之前先将P1置0xffkey=P1;//读取P1口的状态P2=key;}#includereg52.h#define uint unsigned int #define uchar unsigned char#define key P2//与if语句中的定义不同，用16进制数表示具体的按键uchar keynum; //定义全局变量，储存P2口的状态uchar code table[]={0x3f,0x06,0x5b,0x4f,0x66,0x6d,0x7d,0x07,0x7f,0x6f,0x77,0x7c,0x39,0x5e,0x79,0x71}; //共阴极数码管从0到f的数组void delay(uint z) { uint x,y; for(x=0;xz;x++) for(y=0;y120;y++);}uchar key_scan()//按键扫描{ uchar key_value=0; if(key!=0xff)//判断是否有案按键按下 { delay(5); //去抖动 if(key!=0xff) key_value=key; } return key_value;}void main(){ P1=0x00;while(1){ keynum=key_scan(); switch(keynum) { case(0xfe): //表示P2^0口的按键被按下 P1=table[0];break; case(0xfd): //表示P2^1口的按键被按下 P1=table[1];break; ca