基于单片机实训板的数字钟设.docVIP

数字钟设计功能描述：用所设计的实训板设计能显示时间和日期的数字时钟。电路图2功能实现：（1．?????? 把“单片机系统”区域中的P1.0－P1.7端口用8芯排线连接到“动态数码显示”区域中的A－H端口上；（2．?????? 把“单片机系统：区域中的P3.0－P3.7端口用8芯排线连接到“动态数码显示”区域中的S1－S8端口上； （3．?????? 把“单片机系统”区域中的P0.0/AD0、P0.1/AD1、P0.2/AD2端口分别用导线连接到“独立式键盘”区域中的SP3、SP2、SP1端口上； 3、程序框图： 设置初值：second=0,minite=0,hour=12设置初值：second=0,minite=0,hour=12Hour=0Hour=24?Minite=60?minite=0,hour=hour+1Second=0,minite=minite+1Second=second+1延时1S分别动态显示小时和分钟；Second=60?Hour=0Hour=24?Minite=60?minite=0,hour=hour+1Second=0,minite=minite+1Second=second+1延时1S分别动态显示小时和分钟；Second=60? 6． 汇编源程序 HOURK BIT P1.2 MINITEK BIT P1.1 SECONDK BIT P1.0 SECOND EQU 30H MINITE EQU 31H HOUR EQU 32H ORG 0000H LJMP START ORG 000BH LJMP INT_T0 ORG 0030HSTART: MOV SECOND,#00H MOV MINITE,#00H MOV HOUR,#12 MOV R0,#00H MOV TMOD,#01H MOV TH0,#3CH MOV TL0,#0B0H SETB EA SETB ET0 SETB TR0NEXT: MOV A,#0F7H MOV P3,A MOV A,HOUR MOV B,#10 DIV AB MOV DPTR,#TABLE MOVC A,@A+DPTR MOV P2,A CALL DELAY MOV A,#0FBH MOV P3,A MOV A,B MOV DPTR,#TABLE MOVC A,@A+DPTR MOV P2,A CALL DELAY MOV A,#0FDH MOV P3,A MOV A,MINITE MOV B,#10 DIV AB MOV DPTR,#TABLE MOVC A,@A+DPTR MOV P2,A CALL DELAY MOV A,#0FEH MOV P3,A MOV A,B MOV DPTR,#TABLE MOVC A,@A+DPTR MOV P2,A CALL DELAYWT: JB SECONDK,NK1 LCALL DELY10MS JB SECONDK,NK1 JNB SECONDK,$ INC SECOND MOV A,SECOND CJNE A,#60,NK1 MOV SECOND,#00H NK1: JB MINITEK,NK2 LCALL DELY10MS JB MINITEK,NK2 JNB MINITEK,$ INC MINITE MOV A,MINITE CJNE A,#60,NK2 MOV MINITE,#00H NK2: JB HOURK,NK3 LCALL DELY10MS JB HOURK,NK3 JNB HOURK,$ INC HOUR MOV A,HOUR CJNE A,#24,NK3 MOV HOUR,#00NK3: MOV A,R0 CJNE A,#20,NEXT1 MOV R0,#0 INC SECOND M