- 1、本文档共51页,可阅读全部内容。
- 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
- 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载。
- 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
ABSTRACT
电子与信息工程学院
本 科 毕 业 论 文
论文题目 基于plc的多路称重系统设计
学生姓名
学 号
专 业 电气工程及其自动化
班 级
指导教师
2016年5月
PAGE \* MERGEFORMAT
PAGE \* MERGEFORMAT I
摘要
PAGE \* MERGEFORMAT
PAGE \* MERGEFORMAT IV
摘 要
在科学技术高速发展今天,工业的发展也趋向高效、自动、智能化。自动、多路称重的高效智能方式已渐渐取代了传统手工、人工的粗略繁琐称重方法,使得工厂生产的效率大幅提高,人力资源得以节省。
本课题设计了一种基于PLC控制的多路称重系统。本课题介绍了该系统的构成及工作原理。系统配以称重传感器、称重信号放大器、PLC、A/D模块、显示屏等。先在程序中设定重量范围,然后工件通过皮带送到称重系统称重。若工件达标,则重量在设定范围内则无相关响应;若工件未达标,则重量超出或低于设定范围,则信号灯起,筛选系统把不达标工件筛选出来。本文主要介绍了称重系统的总体设计与软件的实现,并用软件进行仿真验证程序,其它相关系统只做简要概述。
关 键 词: 称重系统;压力传感器;PLC;重量范围
ABSTRACT
ABSTRACT
In the rapid development of science and technology today, the development of the industry also tend to be highly efficient, automatic, intelligent. Automatic, multi-channel weighing intelligent method has gradually replaced the traditional manual, manual, a rough and cumbersome weighing method, so that the efficiency of plant production is greatly improved, human resources can be saved.
In this paper, we design a multi-channel weighing system based on PLC control. The composition and working principle of the system are introduced in this paper. The system is equipped with weighing sensor, weighing signal amplifier, PLC, A/D module, display screen and so on. First in the program to set the weight range, and then the workpiece through the belt to the weighing system. If the workpiece is up to the standard, the weight is not related to the range of response; if the workpiece is not up to the standard, the weight is beyond or below the set range, the signal lamp, the screening system is not up to the standard workpiece. This paper mainly introduces the overall design of the weighing system and the realization of the software, and uses the software to carry on the simulation to verify the program.
KEY WORDS: Weighing system;Pressure transducer;PLC;Wei
您可能关注的文档
- 纸张表面喷涂设备的设计本科毕业设计毕业论文.doc
- 创新杯大学生数学建模竞赛航班延误问题论文.doc
- 翰林轩书吧管理系统毕业论文.doc
- 浅析育鲲轮调距桨系统控制原理及螺距调节故障分析毕业论文.doc
- 关于组织开展2016年优秀教育技术毕业论文、课题研究等九项电教学术作品评选活动的通知.doc
- 护理学院优秀调研毕业论文不同急救普及方式对毕节市民众实施急救可能性影响的调查研究.doc
- 熟悉人脸范式提高了p300脑机接口系统的性能毕业论文.docx
- 电泳颗粒的微胶囊化研究进展印刷工程专业毕业论文.doc
- 基于软件流水线的Needleman-Wunsch算法并行化设计毕业论文.doc
- IPTV机顶盒的浏览器设计与实现毕业设计论文.docx
文档评论(0)