关于输料皮带机的三维cad的研究与设计.docVIP

摘要 本次毕业设计是关于输料皮带机的三维CAD的研究与设计。首先对输料皮带机作了简单的概述；接着分析了带式输送机的选型原则及计算方法；然后根据这些设计准则与计算选型方法按照给定参数要求进行选型设计；接着对所选择的输送机各主要零部件进行了校核。设计过程大致分为以下 个方面,首先绘出输料皮带机相关图纸，然后根据所绘出的二维图纸进行三维建模，采用工具进行实体建模，主要是头架，中间架，尾架，拉锁组件的三维建模，最后将这些三维模型组装成为输料皮带机的机架。然后利用ANSYS分析软件对所组装的机架进行有限元分析，找出两个拉索在梁上的最优位置，使得两根拉索在工作的过程中受力大小近似相等，而且使得梁上的危险截面处的弯矩最小。此外，利用MATALAB软件辅助手工计算，找出拉索在梁上的最优位置。然后与软件分析的最优位置进行比较，得出拉索在梁上所处的最优位置。最后，对梁进行强度校核，判断所建模型是否符合强度要求。 关键词：带式输送机； PROE建模； ANSYS有限元分析； MATLAB软件 Abstract The design is a graduation project about the belt conveyor used in coal mine. At first, it is introduction about the belt conveyor. Next, it is the principles about choose component parts of belt conveyor. After that the belt conveyor abase on the principle is designed. Then, it is checking computations about main component parts. The ordinary belt conveyor consists of six main parts: Drive Unit, Jib or Delivery End, Tail Ender Return End, Intermediate Structure, Loop Take-Up and Belt. At last, it is explanation about fix and safeguard of the belt conveyor. Today, long distance, high speed, low friction is the direction of belt conveyor’s development. Air cushion belt conveyor is one of them. At present, we still fall far short of abroad advanced technology in design, manufacture and using. There are a lot of wastes in the design of belt conveyor. Keyword: belt conveyor; PROE modeling; ANSYS finite element analysis; MATLAB software; 目录 TOC \o 1-3 \h \z \u HYPERLINK \l _Toc358826917 摘要 PAGEREF _Toc358826917 \h 1 HYPERLINK \l _Toc358826918 Abstract PAGEREF _Toc358826918 \h 2 HYPERLINK \l _Toc358826919 1 绪论 PAGEREF _Toc358826919 \h 6 HYPERLINK \l _Toc358826920 1.1输料皮带机的国内外研究与发展 PAGEREF _Toc358826920 \h 6 HYPERLINK \l _Toc358826921 1.1.1输料皮带机的简介 PAGEREF _Toc358826921 \h 6 HYPERLINK \l _Toc358826922 1.1.2输料皮带机的国外研究成果 PAGEREF _Toc358826922 \h 7 HYPERLINK \l _Toc358826923 1.1.3 输料皮带机的国内研究现状 PAGEREF _Toc358826923 \h 8 HYPERLINK \l _Toc358826924 1.1.4 输料皮带机的发展趋势 PAGEREF _Toc358826924 \