《环保型聚丙烯腈酸铵水性粘结剂在摩托车缸体砂芯上的应用研究》-毕业设计论文（学术).docVIP

精品 XX大学本科学生毕业设计（论文） 环保型聚丙烯腈酸铵水性粘结剂在摩托车缸体砂芯上的应用研究 校徽 学 生：XXX 学 号：20XXXXX 指导教师：XXX 专 业：XXXX XX大学XX学院 二OXX年X月 Graduation Design(Thesis) of XX University Environmental protection polyacrylonitrile acid aqueous binder ammonium in motorcycle cylinder cores on the application studies Undergraduate:XXX Supervisor:Prof.XXX Major: XX XX XX XXX XX 2XXX 精品 摘 要 腈纶废丝是纺织业产生的一种废料，数量较为可观。虽然此前已有利用其水解液作铸造粘结剂的尝试，但因其固有的湿压强度低，耐烘性差，粘模和烘干后易返潮等缺点而未能达到利用它取代污染环境的合脂粘结剂的目的。 本文研究重点是在前期水解研究已取得成功并已进行一些生产试验的基础上，进一步针对XX主城周边的摩配厂家进行更细致的试验。对粘结剂的配方、加入量、混制工艺、烘焙规范进行适应性研究，期望制备出满足摩托车缸体坭芯生产所需性能的腈纶废丝水解液粘结剂。 关键词：水溶性粘结剂，腈纶废丝，铸造粘结剂 精品 ABSTRACT As a waste produced in textile, the number of polyacrylonitrile waste silk is impressive. Although previously some attempts have been made to use its hydrolysis liquid as foundry binder, because of its shortcomings such as the inherent strength of wet strength is very low, it is poor to resist drying, and is easy to adhere to mold and to get damp after drying, we fail in using it to replace Synthetic resin binder. The main purpose of this paper is In previous hydrolysis research has successful and have some production based on the test of chongqing urban peripheral for further waitan manufacturers more sophisticated test. The formula of binder, join quantity, mix system technology, baking standard adaptive research ， finally to meet the requirements that water soluble binder of polyacrylonitrile waste silk can be used in actual manufacture. Key words：Water-soluble adhesive，Acrylic waste silk，Binder Casting 精品 目 录 TOC \o 1-3 \h \z \u HYPERLINK \l _Toc295821417 摘 要 PAGEREF _Toc295821417 \h I HYPERLINK \l _Toc295821418 ABSTRACT PAGEREF _Toc295821418 \h II HYPERLINK \l _Toc295821420 1 绪言 PAGEREF _Toc295821420 \h 1 HYPERLINK \l _Toc295821421 1.1腈纶废丝水解液作铸造型芯粘结剂应用现状 PAGEREF _Toc295821421 \h 1 HYPERLINK \l _Toc295821422 1.2 往届同学毕业设计得出的结论 PAGEREF _Toc295821422 \h 2 HYPERLINK \l _Toc295821423 2 腈纶及其生产方法 PAGEREF _Toc295821423 \h 3 HYPERLINK \l _Toc295821424 2.1腈