- 1、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。。
- 2、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载。
- 3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
- 4、该文档为VIP文档,如果想要下载,成为VIP会员后,下载免费。
- 5、成为VIP后,下载本文档将扣除1次下载权益。下载后,不支持退款、换文档。如有疑问请联系我们。
- 6、成为VIP后,您将拥有八大权益,权益包括:VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
- 7、VIP文档为合作方或网友上传,每下载1次, 网站将根据用户上传文档的质量评分、类型等,对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档
查看更多
基于IEEE1394及工业以太网的数控伺服总线硬件设计与分析-控制理论与控制工程专业论文
Hardware Design and Analysis of CNC Servo Bus Based on IEEE1394 and Industry Ethernet
ABSTRACT
As a main component of the CNC(Computer Numerical Control) machine tool, CNC system determined the performance、functions、
reliability and cost of the whole CNC machine tool. It’s necessary to build a high-grade CNC system, especially a high-speed、high reliability
bus between CNC control unit and servo unit in order to realize the excellent performance of a high-grade CNC machine tool, such as
high-speed and high-precision machining, as well as multi-channal,
multi-axis control and complex processing .
In this thesis, IEEE1394 bus and Industry Ethernet bus are applied in the servo control system for CNC machine tool, according to the demands of developing a high-grade CNC machine tool. An IEEE 1394 protocol based 1394 I/O module and an Industry Ethernet protocol based Ethernet front-end module are designed and used as the communication interfaces between servo units of CNC machine tool and the bus. These two communication modules both use DSP chip TMS320F2812 as the core controller. The 1394 I/O module could communicate with 1394 bus through the 1394 chip TSB43AA82 and exchange data with machine tools through the I/O ports of DSP; The Ethernet front-end module could communicate with Ethernet bus through the Ethernet chip AX88783 and exchange data with motion controller through dual-port RAM chip CY7C026A.
In this thesis, the IEEE1394 and Ethernet protocol standards are summarized; The hardware design and device drive programming of 1394 I/O module and Ethernet front-end module are introduced in details; Then, a series of function and performance tests of these two communication
modules are taken; Finally, the point of merging the IEEE1394 and Etehrnet protocols, and developing a new Industry Ethernet procol which could be specifically used in CNC system is proposed.
Keywords: IEEE 1394, Industry Ethernet, CNC system, servo bus, Time-Delay
目 录
摘 要 ................
您可能关注的文档
- 基于IDE硬盘的大容量语音记录仪的研制-物理电子学专业论文.docx
- 基于IDL肺部肿瘤医学图像处理系统的设计与实现-软件工程专业论文.docx
- 基于IDMA宽带卫星通信系统的接入控制及资源分配方法-信息与通信工程专业论文.docx
- 基于IDE硬盘的数据采集存储系统研究-水声工程专业论文.docx
- 基于IDA的无粘结预应力装配式框架结构地震易损性分析-结构工程专业论文.docx
- 基于IDRA的空天网络通信研究-通信与信息系统专业论文.docx
- 基于iDose4迭代技术重建的多模式CT检查在缺血性脑卒中疾病中的临床应用-影像医学与核医学专业论文.docx
- 基于IDP理论的中国对外直接投资阶段的实证分析-金融学专业论文.docx
- 基于IDL的资源三号卫星图像处理分析与质量评价软件研究与实现-摄影测量与遥感专业论文.docx
- 基于IDXP的网络入侵检测系统-计算机应用技术专业论文.docx
- 基于IEEE1394的总线事务层IP核设计与验证-软件工程专业论文.docx
- 基于IEEE1394的SoC软硬件协同设计和验证-软件工程专业论文.docx
- 基于IEEE1451标准的NCAP的设计与实现-电路与系统专业论文.docx
- 基于IEC61850的网关设计-电气工程专业论文.docx
- 基于IEEE1394总线的虚拟仪器控制系统的研究-控制理论与控制工程专业论文.docx
- 基于IEEE1451标准的总线化塔机智能监测系统及规范分析-机械电子工程专业论文.docx
- 基于IEC61850的智能变电站通信网络实时与可靠性研究-电气工程专业论文.docx
- 基于IEEE1500的SoC中存储器内核内建自测试设计研究-检测技术与自动化装置专业论文.docx
- 基于ieee1451标准网络传感器的研究-控制理论与控制工程专业论文.docx
- 基于IEEE1588v2的精确时钟同步系统的设计与实现-软件工程专业论文.docx
文档评论(0)