金属纤维表面改性技术的研究-材料学专业论文.docxVIP

西安建筑科技大学着改性剂浓度的增大表面摩擦系数明显降低。并且改性剂浓度增大到一定程度 西安建筑科技大学 着改性剂浓度的增大表面摩擦系数明显降低。并且改性剂浓度增大到一定程度 时，纤维表面摩擦系数不再变化。 5、采用浓度为O．4％PEO改性纤维，其表面摩擦系数已经达到理论要求值。浓度增 到O．5％时，摩擦系数变化趋于缓慢。而硅油改性剂，浓度在2％时，摩擦系数 降低程度开始趋于缓慢，但在1．5％时改性纤维摩擦系数已经达到理论要求值。 6、同样的腐蚀条件下，纤维越细，腐蚀率越大。经PEO改性的纤维烧结后，腐蚀 率随着改性剂浓度的增大而增加，但浓度在O．4％以下时，腐蚀率符合纤维的性 能要求，浓度增至O．5％腐蚀率突然增大，超出了性能要求。经硅油改性的纤维 烧结后0-2％浓度范围内，腐蚀率变化不明显，符合性能要求。 7、纤维越细，表面摩擦系数越大，成网越难。纤维经改性后由于表面摩擦系数降 低，成网情况明显改善，纤网成品率也得到提高。经不同改性剂改性后成网效 果改善不同。经PEO改性的纤维，成网效果有一定改善，经硅油改性的纤维， 成网效果明显改善。 8、同一丝径纤维，卷曲纤维较平直纤维铺网效果好，成网成品率也高。因此细丝 径的纤维经卷曲工序处理后，会提高纤网的质量。 关键词：超细不锈钢纤维 表面改性 摩擦系数 纤网均匀性 II 西安建筑科技大学The 西安建筑科技大学 The study on surface modified technology for medic fiber Specialty：Material Science Name： Guo ping lnstrunor：．Prof．Xi Zheng ping Yangyan an Abstract Metallic fiber is an important field in material subject．Stainless steel fiber not only has its o、vner good properties，but also has its remarkable physical properties．At present， the most common method ofmaking metallic fiber is the bundle—drawing technology．，Its making process makes fiber’S interior structure and surface property occur remarkable variation．So its price has doubled．Stainless steel fiber cannot only resistant to corrosion and high temperature，but also be soft and be spun．So it is widely used in many fields．Its manufacture craft is special，and any coefficient’S change for the process of drawing and heat treatment will affect the deformation of fiber．Of 1ate years．with the development of science，special property of superfine stainless steel fiber is paid more attention，such as metallic fiber felt of high filtering accuracy is made of superfine metallic fiber,but superfine fiber’S surface question makes webbing not uniform，and affects felt’S filtering accuracy．So it is necessary to improve the surface of superfine fiber and not to influence the property of product．Till now,this research is very lack,SO it is necessary for US to study the metallic fiber．In the paper we use surface modification reagent to improve fiber’S surface．To