毕业论文-单层钢筋混凝土结构厂房抗震设计（27m双跨）.docVIP

单层钢筋混凝土结构厂房抗震设计（27m双跨) PAGE II PAGE 42 本科毕业设计 土木工程 单层钢筋混凝土结构厂房抗震设计（27m双跨） The seismic design for the single floor industrial building of reinforced structure（27m+27m） 单层钢筋混凝土结构厂房抗震设计（27m双跨） 摘要：厂房位于宁波市郊区，是一所生产用的混凝土厂房。建筑面积为3634.5 .厂房采用混凝土排架结构体系，主材采用钢筋混凝土，屋面板采用预应力混凝土屋面板，柱为混凝土预制住，场内每跨设20/5t起重机一台，基础为柱下独立基础，基础标高-0.700m。墙体采用240清水墙。 建筑等级：耐久等级为Ⅱ级，耐火等级为Ⅱ级，设防烈度为7度。地面粗糙度为B类。地下水位在-4.0m处。 关键词：混凝土排架结构 ;吊车 ;混凝土预制柱 ;柱下独立基础 The seismic design for the single floor industrial building of reinforced structure（27m+27m） Abstract:The industrial building lies in suburb of Ningbo, is a building of Reinforced structure .The total area is3634.5 mm2. The industrial building adopts concrete bent construction, primary using the material of reinforced. However, the proof of the building adopts the precast slap. And the column use the precast column . There is one crane in each span. The foundation is a single foundation under the column, with a elevation level of -0.700 m. The wall is made up of the clay and the width is 240mm Class of construction: Durable grade Ⅱ，fire protection rating Ⅱ,earthquake intensity 7 degrees. The ground asperity belongs to B and the underground water level at -4.0m. Key words：concrete bent construction；crane；precast column；single foundation under the column 目　录 TOC \o 1-3 \h \z \u HYPERLINK \l _Toc16933 目　录 PAGEREF _Toc16933 III HYPERLINK \l _Toc24432 1 设计资料 PAGEREF _Toc24432 1 HYPERLINK \l _Toc3095 1.1 设计资料 PAGEREF _Toc3095 1 HYPERLINK \l _Toc28347 1.2 基本要求 PAGEREF _Toc28347 1 HYPERLINK \l _Toc27252 1.3 地质抗震条件 PAGEREF _Toc27252 1 HYPERLINK \l _Toc13319 2 建筑方案设计 PAGEREF _Toc13319 2 HYPERLINK \l _Toc27141 2.1 厂房平面设计 PAGEREF _Toc27141 2 HYPERLINK \l _Toc29974 2.2 构件选型与布置 PAGEREF _Toc29974 3 HYPERLINK \l _Toc23864 2.2.1 屋面板和嵌板 PAGEREF _Toc23864 3 HYPERLINK \l _Toc6021 2.2.2 天沟板 PAGEREF _Toc6021 4 HYPERLINK \l _Toc9328 2.2.3 屋架，天窗及屋架支撑 PAGEREF _Toc9328 5 HYPERL