轴承ansys建模系统.ppt

July 30, 1999 轴承座 专题 6F 实体建模: 自上而下 6F. 实体建模：自上而下轴承座 说明 建立轴承座的1/2对称实体模型。 以p-block.db 文件名保存数据库文件 6F. 实体建模：自上而下轴承座 1. 按教师指定的工作目录，用“p-block”作为作业名， 进入 ANSYS 2. 打开等轴视图方位: 按[ISO] 或用命令: /VIEW,1,1,1,1 3. 创建轴承座的基础 : Main Menu Preprocessor Modeling Create Volumes Block By Dimensions 输入 X1 = 0, X2 = 3, Y1 = 0, Y2 = 1, Z1 = 0, Z2 = 3,然后按[OK] 或用命令: /PREP7 BLOCK,0,3,0,1,0,3 6F. 实体建模：自上而下轴承座 4.将工作平面移到 X=2.25, Y=1.25, Z=.75: Utility Menu WorkPlane Offset WP by Increments … 设置 X,Y,Z Offsets = 2.25, 1.25, 0.75 设置XY, YZ, ZX Angles = 0, -90, 0, 然后按 [OK] 或用命令: WPOFF, 2.25, 1.25, 0.75 WPROT, 0, -90, 0 6F. 实体建模：自上而下轴承座 5. 创建直径为0.75 英寸深度为-1.5 英寸的圆柱 : Main Menu Preprocessor Modeling Create Volumes Cylinder Solid Cylinder 输入Radius = 0.75/2 输入Depth = -1.5, 然后按 [OK] 或用命令: CYL4, , ,0.75/2, , , ,-1.5 6. 将圆柱考贝到DZ=1.5的新位置 : Main Menu Preprocessor Modeling Copy Volumes + 拾取柱体 (体号 2),按 [OK] DZ = 1.5, 按 [OK] 或用命令: VGEN,2,2, , , , ,1.5, ,0 6F. 实体建模：自上而下轴承座 7. 从轴承座基础中挖出两个圆孔: Main Menu Preprocessor Modeling Operate Booleans Subtract Volumes 拾取轴承座基础的体 (体 1), 按 [OK] 拾取两个圆柱体 (体 2 和体3), 然后按 [OK] 或用命令: VSBV, 1, ALL 6F. 实体建模：自上而下轴承座 8. 在整体坐标系中改变工作平面的相对位置: Utility Menu WorkPlane Align WP with Global Cartesian 或用命令: WPCSYS,-1,0 VPLOT 9. 创建套筒托架的基础: Main Menu Preprocessor Modeling Create Volumes Block By 2 Corners Z WP X = 0 WP Y = 1 Width = 1.5 Height = 1.75 Depth = 0.75, then [OK] 或用命令: BLC4,0,1,1.5,1.75,0.75 10. 将工作平面移到套筒托架的正面: Utility Menu WorkPlane Offset WP to Keypoints + 拾取正面左角顶部的关键点,按 [OK] 或用命令: KWPAVE, 16 6F. 实体建模：自上而下轴承座 11. 创建套筒托架的拱: Main Menu Preprocessor Modeling Create Volumes Cylinder Partial Cylinder 输入WP X = 0 输入WP Y = 0 输入Rad-1 = 0 输入Theta-1 = 0 输入Rad-2 = 1.5 输入Theta-2 = 90 输入Depth = -0.75, 然后按 [OK] 或用命令: CYL4,0,0,0,0,1.5,90,-0.75 6F. 实体建模：自上而下轴承座 12.通过套筒托架的孔创建圆柱: Main Menu Preprocessor Modeling Create Volumes Cylinder Solid Cylinder WP X = 0 WP Y = 0 Radius = 1 Depth = -0.1875,然后按 [Apply] WP X = 0 WP Y = 0 Radius = 0.85 Depth = -2, 然后按 [