JBT 7184.2-1995冲模钢板模座 对角导柱下模座.pdf

中华人民共和国机械行业标准JB/T 7184. 2-冲模钢板模座·对角导柱下模座主题内容与适用范围本标准规定了冲模钢板模座对角导柱下模座的技术条件、尺寸规格、材料、热处理要求及标记本标准适用于冲模滑动导向钢板模架和冲模滚动导向钢板模架。引用标准JB/T 7183冲模钢板模架零件技术条件GB 699优质碳素结构钢技术条件GB 700碳素结构钢GB 8845冲模术语模座的技术紊件和尺寸规格3.1技术条件按JB/T 7188的规定。3.2尺寸规格见图和表。:6AsTA18图机械工业部1995-03—21批准1995--07-01 实施34 JB/T 7184. 2--95表mm凹模周界D(R7)Di(R7)BtHFsS1基本极限基本极限StMxtTB尺寸偏差尺寸偏差10010020032361361920125125200326113619208032160160200329613619204020020022440401201442425--0. 020-- 0. 02040-0. 041--0. 0412502502244017044242532125125224321601920406116016025040408017024252001002002504040120702425250250250404017017024250. 025 0. 025315.31526550452251753032155M12X250. 050-.0. 05016016028040402002425-0. 0200. 020200-0. 041 0. 04120028040401202525012525028050451601903032100315315280 50452259032155M12X252804004005045310.903032.220°20020033550451102453032250250335503024532100315160315335504522524530321554004005045322203102453050050033550452453032320-0. 025 .- 0. 025-0.050 0. 05025025037550160285303280M12X 253153153755045225285303215520040040037550453102853032220500500400895539029038315425505021532530321454004004506355290340384020025050050045063553903403840300M16X 3063063045063555203403840430 JB/T 7184. 295续表凹模周界D(R7)D,(R7)BH基本极限基本极限SMxtL.尺寸偏差尺寸镐差315315530638840.1154004005306.35529042038402003155005005606363374434485028063630630560504434485038063M16X 30-0.025-0.025-0. 050-0. 05040040063063632745044850180500500630636337450448502804006306306308063504.50448503808008001 630806367450448550M20 X 35材料和热处理要求4.1 材料45 钢 GB 699.凹模周界L×B小于400×250的滑动导向模座可用Q235一A钢GB700。4.2热处理要求45 钢调质 HRC26～30。5标记本标准规定的模座标记由下列要素组成下模座;a.b.模座的凹模周界 L×B,c.-模座厚度 H;d.材料;·本标准编号。e.°示例：凹模周界L=125mm、B=100mm、模座厚度H=32mm、材料为45钢的对角导柱下模座的标记如下：下模座125×100×3245.JB/T 7184. 236