真空低压消失模壳型铸造和消失模铸造铝合金组织和性能对比.docVIP

第 23 卷第 1 期 Vol.23 No.1  中国有色金属学报 The Chinese Journal of Nonferrous Metals  2013 年 1 月 Jan. 2013 文章编号：1004-0609(2013)01-0022-07 真空低压消失模壳型铸造和 消失模铸造铝合金组织和性能对比 蒋文明 1, 2 ，樊自田 2 ，刘德均 2 (1. 武汉工程大学 机电工程学院，武汉 430073； 2. 华中科技大学 材料成形与模具技术国家重点实验室，武汉 430074) 摘 要：利用光学显微镜(OM)、扫错电镜(SEM)等对真空低压消失模壳型铸造和消失模铸造 A356 铝合金的组织 和性能进行对比分析。结果表明：真空低压消失模壳型铸造 A356 铝合金组织比消失模铸造 A356 铝合金组织细 小、致密，其初生相晶粒尺寸和共晶硅尺寸都远小于消失模铸造铝合金的，孔隙率低于消失模铸造铝合金的、密 度高于消失模铸造铝合金的。真空低压消失模壳型铸造 A356 合金的拉伸断裂方式以韧性断口为主，消失模铸造 铝合金的断裂方式以脆性断口为主；铸件经 T6 热处理后的抗拉强度、伸长率和布氏硬度分别达到 278.27 MPa、 8.10 %和 93.1HB，较消失模铸件的分别提高了 20.2 %、166.4 %和 17.6 %；其铸件表面质量也优于消失模铸件的 表面质量。 关键词：铝合金；真空低压消失模壳型铸造；消失模铸造；组织；性能 中图分类号：TG292 文献标志码：A  Comparison of microstructures and properties of aluminum alloy between expendable pattern shell casting with vacuum and low-pressure and lost foam casting JIANG Wen-ming 1,2 , FAN Zi-tian 2 , LIU De-jun 2 (1. School of Mechanical and Electrical Engineering, Wuhan Institute of Technology, Wuhan 430073, China? 2. State Key Laboratory of Material Processing and Die ＆ Mould Technology, Huazhong University of Science and Technology, Wuhan 430074, China) Abstract: The microstructures and properties of A356 alloy produced using expendable pattern shell casting process with vacuum and low-pressure (EPSC-VL) were compared with those of lost foam casting (LFC) process by OM and SEM techniques. The results show that microstructure of A356 alloy produced by EPSC-VL is finer and denser than that of LFC, and the sizes of the primary phase and eutectic silicon are far less than those of LFC, its porosity is less than that of LFC, and its density is higher than that of LFC. The fracture mechanism of A356 alloy obtained using EPSC-VL mainly shows ductile fracture, and that of A356 alloy obtained using LFC mainly shows brittle fracture. The tensile strength, elongation as well as hardness of A356 after T6 treatment alloy fabricated using EPSC-VL are respectively 278.27 MPa, 8.10% an