主题：仪表放大器--常见的应用问题和解决方案.docVIP

主题：仪表放大器--常见的应用问题和解决方案 问答集锦： [问：zw-wu] 我现在用了AD620与AD8221仪表放大器,但在使用过程中,有时输出会出现一些干扰信号,不知这些仪表放大器怎样才能减小无用信号,提高共模抑制? [答：Forest] 你可以在输入端之前加入低通滤波器，就可以减少干扰信号了。今天的资料中就有详细的介绍。? [问：zhangxk] 在应变片式传感器（Load cell）的放大、转换电路中，要将A/D分辨率提高到19位以上，并且转换速度大于50sps，应选用什幺样的芯片组合，或者电路设计中应该考虑哪些因素？? [答：Jing] you should pay attentation to the throughput that will be trade off with your accuracy.You should also pay attentation to your input range and offset I think you can refer to our AD7730L or AD7799 .If you just want to use AMP+ADC , you can consider AD8230.Its a chopper-stable instrument amplifier.? [问：xianluc] 如何将设计AD623的输入电路，使AD623单电源+5V供电时，输出信号为0～+5V？? [答：Mariah] In single supply condition, the input common mode voltage is very critical to get the rail to rail output. One good tool to analyze the circuit of AD623 in single supply condition can be got from the link below:/Analog_Root/static/techSupport/designTools/interactiveTools/inamp/inamp.html?inamp=AD623%205V? [问：zzb6503] 在设计电路时，怎样尽可能使仪表放大器抑制50Hz市电干扰？? [答：Forest] AD8221仪表放大器放大器本身就具有很强的共模抑制比，他可以在一定程度上抑制市电的干扰。另外，我们建议在你后续的模拟和数字电路加入带阻滤波器。? [问：zcw0707] 在测量微小电流时，需要串入隔离放大器，怎幺减小隔离放大器带来的影响？? [答：Yiming] 如果一定要采用隔离放大器，那幺隔离放大器的性能不应该恶化输入信号，也就是选用低噪声的隔离放大器。? [问：zhangxk] 如何实现应变片式传感器（Load cell）的交流激励、放大及转换？? [答：Jing] You can use ratiomeric method and AC extinction.AC Excitation can be used to cancel out offset errors, regardless of their source.??AC Excitation here means that 2 sets of readings are taken, with the excitation voltage to the bridge reversed.??Subtracting the 2 readings cancels out the offset errors, as shown in the boxed equation.??This technique requires that the readings be stored and subtracted.??This is an effective technique, but if you implemented this with discrete components you would add more error than you were subtracting.? [问：metrolog] 现在设计的仪表放大器失调电压的温度系数可达到10nV/K吗？? [答：Steve] The lowest drift instrumentation amplifier we have is the AD8230 which has 50nV/C. The AD8555 has 65nV/C and the AD8553 has 100nV/C. We do not have any