各种脱硫烟囱及烟囱内筒防腐方案的分析.docVIP

各种脱硫烟囱及烟囱内筒防腐方案的脱硫烟囱及烟囱内筒防腐方案的主要从技术角度对目前市场上各种防腐方案进行了对比，主要涉及有：乙烯基酯树脂玻璃鳞片胶泥、乙烯基酯树脂胶泥玻璃钢复合、乙烯基酯树脂胶泥勾缝砖板衬里（含泡沫玻化砖、耐酸砖、耐酸陶瓷等方案）、耐酸KP胶泥、KP胶泥勾缝砖板衬里、OM涂料、钛合金复合合金板、混元体方案、环硅聚合物杂化方案 关键词：烟气脱硫、烟囱、防腐、玻璃鳞片胶泥 Analysis of Various Anti-corrosion Solutions For Desulfurization Stack FGD Stack Anti-corrosion Articles(Part III) Jiang Xianlong,Qian Yongjia, Yang Hua, Zhou Guoyou, Zhang Ming, Chen Fang (Changzhou Huake Resin Co., Ltd. Changzhou, 213102,China) Abstract: This series of articles mainly focus corrosion properties of FGD stack, necessity of FGD stack anti-corrosion engineer, anti-corrosion materials and stack anti-corrosion standards. This Part III is “Analysis of Various Anti-corrosion Solutions For Desulfurization stack”. From a pure technical point of view, this paper introduces and compares a variety anti-corrosive strategies of desulfurization stack in domestic market, these strategies are mainly the following as: vinyl ester resin glass flake compound liner, combination of vinyl ester resin glass flake compound and FRP, brick lining board with vinyl ester resin glass flake compound(including foam tiles, acid-resistant bricks, acid-resistant ceramic tiles), acid-resistant KP-1 clay, brick lining board with KP-1 clay, OM coatings, titanium alloys, Hun Yuan body method, ring silicon polymer hybrid materials method, SAUEREISEN flexible liner spray method, PFA weldable Teflon plastic liner, FRP coupon splice method, the whole FRP flue and stack method. Key Words: FGD, Stack, Anti-corrosion, Flake compound. 0 引言 由连载文章（一）、（二）可知：强腐蚀环境，并且伴随着干湿交变、温度交变，这就是脱硫后烟囱内筒所处的环境，因此务必对烟囱内筒或整个烟囱进行防腐处理。方案：防腐、抗渗、防脱落。防腐由材料本身材质的耐酸性，尤其是高温下的耐酸性决定的；抗渗主要由防腐层厚度、有机无机成份固化物的致密性决定的；防脱落主要由施工质量优劣、基材处理好坏、防腐层本身的耐温骤变性能优劣、防腐层的耐应力变化优劣决定的。 防腐材料要求与清洁处理后烟囱砖内筒有良好的粘结和覆盖作用，防腐层应 完全适用于脱硫工况(湿烟气，45℃～50℃)和非脱硫工况(干烟气，℃～15℃)交替运行的条件，防腐涂料层要具有高抗酸性、耐温性并长期保持密实不开裂，防腐层固化后具有一定的韧性和强度并保持优异的伸展性，在较宽的范围内长期保持稳定，防腐层应保证在烟囱长期运行的℃～15℃工作温度环境下膨胀可逆并能够保持良好的弹性；且短时间应能够承受瞬间180℃高温冲击(锅炉事故状态)。一般确保防腐系统正常使用寿命达到年至年的使用寿命(依据机组运行年限而定)。防腐方案应特别注意对牛腿、烟囱出口、烟囱正压区域、烟