commentsfor resultsofvotingon n w i p amendmentsto13628-1（commentsfor resultsofvotingon n w i p amendmentsto13628-1）.docVIP

下载本文档

4
0
约5.27万字
约 29页
2017-01-24 发布于四川
举报
版权申诉

commentsfor resultsofvotingon n w i p amendmentsto13628-1（commentsfor resultsofvotingon n w i p amendmentsto13628-1）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

FR 3.1.14 te Is the intention to distinguish CRAs from Stainless Steels? It can be inferred from other sections such as 6.4.3 and 6.4.5 that stainless steels are also CRAs. Clarify if CRAs have less than 50% iron; example : Ni based alloys. Otherwise mention as examples that austenitic stainless steels (eg 316L) and Duplex stainless steel are also considered as CRAs in this standard. FR 6.3.4 3rd bullet point te Why specifically mention glass reinforced plastics ? Use a more general term for these type of materials non subject to corrosion : non-metallic composites. FR 6.3.4 te Cathodic protection standards mentioned are DNV RP-B401 and NACE RP0176 Mention also ISO 15589-2 US Entire document Technical The US requests that these comments be fully considered as DIS comments – reviewed and resolved prior to the issuance of the first DIS ballot, with resolutions noted in an included comment register; As needed to resolve comments. US Entire document Technical The material contained in this ballot should be compared and aligned to the content of proposed API 17P / ISO 13628-15. It should be noted that overlapping material will be withdrawn on the publication of 17P/-15; Align documents and add Introduction note “Upon publication of API 17P / ISO 13628-15, the requirements/ recommendations in (pertinent clauses) for (pertinent products) in this International Standards 13628-1 will be superseded.” US 6.4.2.2 Table 4 Technical Verify the that temperature ranges for the materials are correct or not. In the past edition of this document (1999), the temp ranges for bolt material were Above 100 (212), Above 46 (115) and -196 to +60 (-320 to +140). The new ranges all start with large negative temps (-46, -100, -196) that are very different than the previous edition. Note that a similar problem appears to exist with the current ediiton Table 1 for bolting material. Also, in the 1999 edition, size range for L7 material was 50 mm, and is 65 now and