板式蒸发式冷凝器传热传质的数值模拟探究.pdfVIP

板式蒸发式冷凝器传热传质的数值模拟探究.pdf

  1. 1、本文档共9页,可阅读全部内容。
  2. 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
  3. 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载
  4. 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
  5. 5、该文档为VIP文档,如果想要下载,成为VIP会员后,下载免费。
  6. 6、成为VIP后,下载本文档将扣除1次下载权益。下载后,不支持退款、换文档。如有疑问请联系我们
  7. 7、成为VIP后,您将拥有八大权益,权益包括:VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
  8. 8、VIP文档为合作方或网友上传,每下载1次, 网站将根据用户上传文档的质量评分、类型等,对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档
查看更多
第34卷 第期 203年2月 制 冷 学 报 0 Journal of Refrigeration Vol.34,No.1 February. 2013 文章编号:0253-4339(2013)01-0010-08 doi:10.3969/j.issn. 0253-4339. 2013. 01. 010 板式蒸发式冷凝器传热传质的数值模拟 董俐言1 王宝龙1 石文星1 李先庭1 李志明2 谭 栋2 (1 清华大学 北京 100084;2 广州市华德工业有限公司 广州 510663) 摘 要 根据能量守恒和质量守恒定律,对板式蒸发式冷凝器中制冷剂、冷却水与空气之间的传热传质过程,建立了热质 交换过程的二维数学模型,由此分析板式蒸发式冷凝器中冷却水温度、空气温度和空气含湿量等参数的分布规律,以及空 气流速、干湿球温度、冷却水喷淋密度和冷凝温度对板式蒸发式冷凝器热流密度的影响,并将模拟结果通过实验进行了验 证,两者之间的误差在10%以内。研究表明:板式蒸发式冷凝器的热流密度随进口空气流速的增加而增大,随湿球温度的 升高而减小,几乎不受进口空气干球温度的影响;热流密度随着冷却水喷淋密度的增加逐渐增大,但增大至一定量后不再 对热流密度有明显影响;冷凝温度越高,其热流密度越大。上述结论对板式蒸发式冷凝器的优化设计具有指导意义。 关键词 蒸发式冷凝器;传热传质;数值模拟;换热器 中图分类号:TK124; TB657.5 文献标识码:A Numerical Simulation on Heat and Mass Transfer of Plate Evaporative Condenser Dong Liyan1 Wang Baolong1 Shi Wenxing1 Li Xianting1 Li Zhiming2 Tan Dong2 (1. Tsinghua University, Beijing, 100084, China; 2.Guangzhou Wide Industrial Co.,Ltd., Guangzhou, 510663, China) Abstract Two-dimensional mathematical model of the heat and mass transfer process among refrigerant, cooling water and air in the plate evaporative condenser was established on the basis of energy and mass conservation. Distributions of cooling water temperature, air temperature and air humidity ratio are obtained. And then studies on influencing factors of plate evaporative condenser heat flux, i.e., air flow rate, cooling water spray density, air dry bulb temperature, wet bulb temperature and the condensing temperature were conducted. Simulation results were verified through experiments, and the error was less than 10%. The results showed that heat flux increased with increasing air flow rate, increasing condensing temperature and decreasing air wet bulb temperature, and is not relevant to air dry bulb temperature. With the increasing cooling water spray density, heat flux gradually increased and then kept constant. These conclusions are instructive for optimization design of plate evaporative

文档评论(0)

希望之星 + 关注
实名认证
文档贡献者

我是一名原创力文库的爱好者!从事自由职业!

1亿VIP精品文档

相关文档