五,空气调1.ppt

2. 上送下回 孔板送风和散流器送风是常见的上送下回形式。 孔板送风和散流器送风，可以形成平行流流型，涡流少，断面速度场均匀的气流 。对于温湿度要求精度高的房间，特别是洁净度要求很高的房间，是理想的气流组织型式。 特 点 这种形式的排风温度也接近室内工作区平均温度。 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 3. 中送下、上回 对于高大房间，送风量往往很大，房间上部和下部的温差也比较大，采用中部送风，下部和上部同时排风，形成两个气流区，保证下部工作区达到空调设计要求，而上部气流区负担排走非空调区的余热量。 显然 下部气流区的气流组织就是侧送侧回。 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 4. 下送上回 适用场合 对于室内余热量大，特别是热源又靠近顶棚 的场合 ，采用这种气流组织形式是非常合适. 特点 由于下送上回时的排风温度大于工作区温度，故室内平均温度较高，经济性好。 但是，下部送风温差不能太大。 可采用旋流送风口。 为此 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 5. 上送上回 这种气流组织形式是将送风口和回风口叠在一起，布置在房间上部。 适用场合 因各种原因不能在房间下部布置风口的场合。 注意 防止气流短路现象的发生。 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 影响因素：送风口的型式、数量和位置； 回风口的位置、送风参数等 1、送风口的型式 1）侧送风口 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 2）散流器 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 3）孔板送风口 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 4）喷射式送风口 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 2、回风口 Evaluation only. Create