双向板及钢筋搭接（Two - way board and steel bar lap joint）.docVIP

下载本文档

1
0
约9.66千字
约 8页
2017-07-21 发布于河南
举报
版权申诉

双向板及钢筋搭接（Two - way board and steel bar lap joint）.doc

1、本文档共8页，可阅读全部内容。
2、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。
3、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
5、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
6、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
7、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
8、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

双向板及钢筋搭接（Two - way board and steel bar lap joint）

双向板及钢筋搭接（Two - way board and steel bar lap joint） According to the specification of concrete structure design (GB 50010-2002), the concrete plate shall be calculated according to the following principles: 1. The supporting board shall be calculated with the single board; (a one-way board) 2 sides supporting plate shall be computed according to the following provisions: (namely two-way slab reinforcement) calculation of reinforcement in the following conditions (a) when the ratio of the long side and short side length less than or equal to 2.0, shall be calculated on the bidirectional board, (b) when the ratio of the length of the long side and short side is greater than 2.0, but less than 3.0, should be calculated on the bidirectional board; When is calculated based on one-way slab along the short edge direction stress, should grow along the edge direction decorate a sufficient number of structural steel, (c) when the ratio of the length of the long side and short side is greater than or equal to 3.0, can be calculated based on one-way slab along the short edge direction stress. If you just distinguish between a single, a two-way board. The simple answer is that the two sides of the plank are unidirectional. The four-sided bearing force plate is bidirectional. There are four commonly used connection methods: tie rolling, welding connection, cold pressure connection and screw connection. In addition to individual cases (if no flame is allowed), weld connections should be used to ensure quality, efficiency and steel. Welding is divided into two forms: welding and welding. Compression welding includes flash butt welding, resistance spot welding and gas pressure welding; Welding includes arc welding and electroslag pressure welding. In addition, the welding of the steel bar and the pre-buried t-connector shall be covered by submerged arc pressure welding. There are four commonly used connection methods: tie rolling, welding connection, cold pressure connection and screw