激光镭雕机调试参数(参考)（Debugging parameters of laser beam engraving machine (Reference)）.docVIP

下载本文档

31
0
约7.25千字
约 8页
2017-07-22 发布于河南
举报
版权申诉

激光镭雕机调试参数(参考)（Debugging parameters of laser beam engraving machine (Reference)）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

激光镭雕机调试参数(参考)（Debugging parameters of laser beam engraving machine (Reference)）

激光镭雕机调试参数(参考)（Debugging parameters of laser beam engraving machine (Reference)） Quote The commissioning parameters for the laser engraving machine N years ago (Reference) (suitable for Han laser machine and laser Valley laser machine) In general, the decisive parameter for the overall effect of the product debugging is the marking frequency and emission time, these two parameters, and the rest of the parameters are mainly for some minor adjustments. A) marking frequency: (range 500 hz------200000 Hz): Theoretically, when the Hz is low (7000------40000), the peak power of the labeled light is stronger, the transmitted light is stronger, and the gasification of the spray ink is better. When the frequency is high (40000 Hz or more), the average power of the labeled light is stronger, and the surface effect of the labeled product is better. For example: white, silver dew effect, the high frequency. B) launch time: (preset value is 1.5us): Theoretically, when the setpoint is 1.5us, the peak power of light is the strongest, and the greater the value is, the weaker the peak power is. Under normal circumstances, marking plastic materials, ABS materials, PC materials and other soft materials, should be launched in a larger time (preferably less than 100US), so as not to burn material. But if the soft material surface is spray some (such as color: white, red, yellow, green) ink, because the ink is not easy to be light to the gasification out, so the launch time is set to 1.5 us. When marking hard materials such as silica gel, rubber and metal, the emission time shall be set at 1.5us. Below we illustrate several spray ink material setting parameters for reference. Because different customers use the ink and spraying method is different, so the adjustment parameters may be different. The following parameter values are a composite of empirical parameters 1., if you want to mark the product material for (transparent plastic material), surface spray (silver, black, etc.) better ga