互换性与技术测量圆柱结合复习题（Review of interchangeability and measurement of cylinders）.docVIP

下载本文档

3
0
约 23页
2017-07-22 发布于河南
举报
版权申诉

互换性与技术测量圆柱结合复习题（Review of interchangeability and measurement of cylinders）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

互换性与技术测量圆柱结合复习题（Review of interchangeability and measurement of cylinders）

互换性与技术测量圆柱结合复习题（Review of interchangeability and measurement of cylinders） Interchangeability of cylindrical exercises I. judgment questions. 1 tolerances can be said to allow maximum deviation of part size. () 2, the basic size of different parts, as long as their tolerances the same value, it can be explained that they require the same accuracy. () 3, the national standard stipulates that the hole refers only to the cylindrical inner surface. () 4, drawing marking 200 -0.021mm diameter shaft, processing the basic dimensions of the more accurate near. () 5, the basic deviation of the hole is the lower deviation, the basic deviation of the axis, that is, the upper deviation. () 6. The size of a hole is 20-0.046 -0.067, and the actual size is 19.962mm. This hole can be judged to be qualified. () 7, no injection tolerance size, that is no tolerance requirements for the size. () 8, the basic deviation determines the location of the tolerance zone. () 9. The allowable variation of the geometric parameters of a part is called geometric tolerance. () 10 the basic deviation refers to the basic size of the same combination of the hole and the axis of the relationship between the tolerance zone. () 11, drawing marking phi 30+0.033 0mm hole, can determine the hole hole Berezovsky benchmark system. () 12, the transition fit may have gaps or may be excessive, so the transition fit may be a gap fit, or it may be interference fit. () 13, the smaller the value of the tolerance, the higher the tolerance grade of the holes and shafts that cooperate with each other. () 14, the hole and shaft fit with a 40H9/n9, can be judged to be a transition fit. () 15, H7/g6 is more important than H7/s6. () 16, the relative position of the hole and shaft tolerance zones reflects the degree of ease of processing. () 17, the minimum clearance of zero coordination and minimum interference equal zero coordination, the two are essentially the same. () 18, the base shaft system matching hole, the lower