基础筏板及基础梁工程施工方案（Construction plan of foundation raft and foundation beam）.docVIP

下载本文档

1
0
约1.82万字
约 13页
2017-08-16 发布于河南
举报
版权申诉

基础筏板及基础梁工程施工方案（Construction plan of foundation raft and foundation beam）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

基础筏板及基础梁工程施工方案（Construction plan of foundation raft and foundation beam）

基础筏板及基础梁工程施工方案（Construction plan of foundation raft and foundation beam） Construction plan of foundation raft and foundation beam I. General Situation and main works: The foundation design of this project is reinforced concrete beam raft foundation. Raft plane is L shape, raft thickness 550mm, width 22.16m, east-west length 44.36m, north-south length 82.78m. The cross section size of foundation beam is 400 * 600mm. Concrete mark is C25, total square amount is 1310m3, the amount of steel used is 150T. In the 16-18 axis, close to the 18 axis, leaving a 1m width through the pouring zone, after pouring with concrete, after the completion of the main casting. Two 、 construction arrangement and main construction plan: The construction work of the formwork is small and the construction is simple, so the construction section is not considered, and the whole is a construction section. The construction of reinforcing bar and concrete is divided into two construction sections after the pouring zone is taken as the boundary, and the construction of simple water flow is simple. The steel works shall be first constructed with 1-16 shafts (I sections), and the concrete shall be poured after self inspection and hidden inspection and acceptance. In the pouring of I section of concrete at the same time continue to tie 18-58 axis (II section) steel bar, self inspection, hidden inspection acceptance, continuous placement of II section of concrete. (I section of concrete is about 660m3, II section of concrete is about 650m3). The main construction methods are as follows: 1. template engineering (1) the template is formed by the combined steel formwork, and the U type ring is connected. After the cushion surface has been cleaned up, it will be assembled at first, and the isolating agent should be painted before the template is assembled. (isolating agent mainly uses engine oil). The main specifications of peripheral side template is 1500 * 300mm, 1200 * 300mm, 900 * 300mm, 600 * 300mm. t