钢筋计算时的一点小常识（A little common sense when calculating steel bars）.docVIP

下载本文档

1
0
约2.03万字
约 15页
2017-08-18 发布于河南
举报
版权申诉

钢筋计算时的一点小常识（A little common sense when calculating steel bars）.doc

1、本文档共15页，可阅读全部内容。
2、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。
3、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
5、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
6、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
7、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
8、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

钢筋计算时的一点小常识（A little common sense when calculating steel bars）

钢筋计算时的一点小常识（A little common sense when calculating steel bars） A little common sense when calculating steel bars: 1, in the reinforced software (A), with a steel, with (B) said two grade steel, with three steel (C) said, with (D) said the new three grade steel (L) said, with cold rolled ribbed bar (N) said, with cold rolled twisted steel 2, the seismic grade of the project is determined by (fortification intensity), (structural type), and (eaves height). 3, seismic grade on the calculation of steel (anchor), (overlap), (encryption area) three aspects of influence. 4, steel 10 mile calculation settings can be (calculation settings), (node settings), stirrup settings, lap setting, stirrup formula five aspects, according to the actual needs of the project to adjust 5 、 in engineering, the support of the beam is (column), the support of the plate is (beam), and the column is supported by (base). (I) three preparations before drawing: 1, drawing: the drawings are divided into: general description, foundation, column, wall and column reinforcement, beam reinforcement, Liang Peijin, plate reinforcement, layout, structure (sporadic stairs node nine parts, etc.) on the component, the 9 parts are independent. 2, analysis of drawing sequence: firstly, according to the general description of the project, based on the first component drawing, then the skirt part of the frame column can use column table function. Then make the wall and the edge reinforcement, because the wall will be the support of the beam. Then it is a coupling beam, because the coupling beam is the support of the secondary beam, so the coupling beam is placed in front of the beam. Then there is the main beam and the secondary beam. After drawing the above component, the plate and the plate reinforcement are very convenient, and the drawing board can be finished quickly by using the point drawing method or the automatic generation of the minimum plate, and then the reinforcing bar is matched with the plate. Fin