教你使用ug软件如何作风扇（Teach you how to use UG software as a fan）.doc

下载文档 降价啦

2
0
约1.37万字
约 15页
2017-08-20 发布于河南
举报
版权申诉
保障服务

教你使用ug软件如何作风扇（Teach you how to use UG software as a fan）.doc

1、本文档共15页，可阅读全部内容。
2、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。
3、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。

教你使用ug软件如何作风扇（Teach you how to use UG software as a fan）

教你使用ug软件如何作风扇（Teach you how to use UG software as a fan） File a 1. Make two hexagons with a radius of 13.5, one orientation is 0 degrees, another is 30 degrees, and build all the parts in the middle. 2. Make a sketch in the zc-xc plane. The dimensions are as follows: 3, the figure 1 steps in the direction of the ZC stretching -18, draft angle 5 degrees rotation; step 2 Sketch, and Boolean operation. 4, do an over point (13.5, 0, 0) and (16.5, 0, -3) radius of 3 arc, and rotate to generate a chip, trim parts of the outer part of the body. 5, the bottom of step 1 adds pocket, dia51h2, pocket, dia25h15ang5, boss, dia14h17, pocket, dia7h16. 6, cross quadrant point as the following two lines, the length of 12.5 and 1+ (-5.5) 7, stretch 12.5 straight line 0-0.7- (-0.75) -0.75; stretch 1+ (-5.5) line 0-12- (-0.3) -0.3; Boolean add, and ring array 6. 8, fillet. R1, R0.5, R0.3. 9, the middle dia7h16 thread. 10, end. File B 1, cylindrical, +z, dia37.5*2h42. 2, Kong, dia31*2h3; dia8.5*2h6. 3, shell, thickness 2, bottom open. 4, shell bottom boss, dia12h26, shell outside hole, dia8 through hole. 5, extract the entity in the xc-zc plane of the bus; over (6, 0, 10) to do parallel and X axis, length of 29.5 straight line. 6, the closed zone (-0.5) -0.5 in the stretching step 5, and offset 7 planes 0.5 (offset, face) apart from the top surface 7, do cylindrical, dia3h18, -z, the bottom of the center of the circle (26.5, 0, 37), Bruga; ctrl+t around the central axis, multiple copies of 5, more objects boolean. 8, in the hole outside the shell to connect two quadrant points, stretching, direction +y, (+3) - - (+5), offset, 0-2, Boolean add. 9, do parallel and zc-xc, distance of -37.5 datum plane, do sketch. 10, do parallel and zc-xc, distance of -180 datum plane, make sketch, after finishing, trim the left tail quickly. 11, in the xc-yc plane semicircle, R180, starting angle 180 degrees, the end angle 0 degrees, tensile height 75. 12. Wrap the lines in steps 9 and 10 to the tangent c